manualshive.com logo in svg

HP StorageWorks SN6000, Command Line Interface Manual

The HP StorageWorks SN6000 offers efficient and reliable storage capabilities for your business needs. Enhance your productivity with this high-performance storage solution. For easy installation and guidance, be sure to download the free User Manual from manualshive.com, providing step-by-step instructions and essential information to optimize your experience.

Share
Download
background image

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 135

clone config port

Description

Duplicates a source port configuration on specified target ports.

Authority

Admin session and a Config Edit session

Syntax

clone config port

[source_port_number] [port_list]

Operands

[source_port_number] [port_list]

Duplicates the configuration of a port given by 

[source_port_number]

 on a set of target 

ports given by [port_list]. [source_port_number] can be 0–23. [port_list] can be a list of port 

numbers or ranges delimited by spaces.

Notes

See 

Table 33

 for a description of the port configuration parameters.

Examples

The following example configures ports 8–19 based on port 0:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) config edit

SN6000 FC Switch (admin) #> clone config port 0 8-19

Port 0 configuration will be cloned to ports 8-19.

  Please confirm (y/n): [n] y

SN6000 FC Switch (admin-config)#> config save

SN6000 FC Switch (admin)#> config activate

SN6000 FC Switch (admin)#> admin end

See also

set config port

, page 195

show config port

, page 236

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Reviews:

No comments

Related manuals for StorageWorks SN6000

3M 45116 Instruction Manual preview
45116
Brand: 3M Pages: 8
Whirlwind W1 Technical Data preview
W1
Brand: Whirlwind Pages: 2
Behringer DI20 User Manual preview
DI20
Brand: Behringer Pages: 12
Ultraflex OB-2C130-SVS Installation Instructions Manual preview
OB-2C130-SVS
Brand: Ultraflex Pages: 16
CommScope SYSTIMAX 360 iPatch PATCHMAX Instruction Sheet preview
SYSTIMAX 360 iPatch PATCHMAX
Brand: CommScope Pages: 6
Aukey CB-CMD29 User Manual preview
CB-CMD29
Brand: Aukey Pages: 8
Aukey CB-CMD2 User Manual preview
CB-CMD2
Brand: Aukey Pages: 8
Aukey CB-CD2 User Manual preview
CB-CD2
Brand: Aukey Pages: 7
PureTools PT-SP-HD28DA User Manual preview
PT-SP-HD28DA
Brand: PureTools Pages: 20
Tripp Lite N816-10M Specifications preview
N816-10M
Brand: Tripp Lite Pages: 2
Grip SHW Assembly And Operating Manual preview
SHW
Brand: Grip Pages: 7
Oriental motor CCEMP4 Series Operating Manual preview
CCEMP4 Series
Brand: Oriental motor Pages: 4
AceProAV AcePro-CE33-1 Quick Installation Manual preview
AcePro-CE33-1
Brand: AceProAV Pages: 8
Panasonic A4S Operation Manual preview
A4S
Brand: Panasonic Pages: 28
Silvercrest SAVK 2000 A1 Operating Instructions Manual preview
SAVK 2000 A1
Brand: Silvercrest Pages: 30
Navilock 20653 User Manual preview
20653
Brand: Navilock Pages: 8
nvent RAYCHEM RayClic-E Installation Instructions preview
RAYCHEM RayClic-E
Brand: nvent Pages: 2
nvent raychem ETL-GLAND-01 Manual preview
raychem ETL-GLAND-01
Brand: nvent Pages: 4

Brands by name

Popular brands

Load more brands