HP StorageWorks SN6000 Command Line Interface Manual Download

Page: 196 / 330

196 Command Reference

ForceOfflineRSCN

Enables (

False

) or disables (

True

) the immediate transmission of

Registered State Change Notification (RSCN) messages when

communication between a port and a device is interrupted. If enabled,

the RSCN message is delayed for 200 ms for locally attached devices

and 400 ms for devices connected through other switches. The default is

False

. This parameter is ignored if

IOStreamGuard

is enabled.

ARB_FF

Send ARB_FF (

True

) instead of IDLEs (

False

) on the loop. The default is

False

InteropCredit

Interoperability credit. The number of buffer-to-buffer credits per port.

means the default is unchanged. Default buffer-to-buffer credits are 16

per port.
Changing interoperability credits is necessary only for E_Ports that are

connected to non-FC-SW-2-compliant switches. Contact your authorized

maintenance provider for assistance in using this feature.

FANEnable

Fabric address notification. Enables (

True

) or disables (

False

) the

communication of the FL_Port address, port name, and node name to the

logged-in NL_Port. The default is

True

AutoPerfTuning

Automatic performance tuning for FL_Ports only. The default is

True

•

If AutoPerfTuning is enabled (

True

) and the port is an FL_Port,

MFSEnable

is automatically enabled.

LCFEnable

and

VIEnable

are overridden to

False

•

AutoPerfTuning

is disabled (

False

MFSEnable

LCFEnable

, and

VIEnable

retain their original values.

LCFEnable

Link control frame preference routing. This parameter appears only if

AutoPerfTuning

False

. Enables (

True

) or disables (

False

)

preferred routing of frames with R_CTL = 1100 (Class 2 responses). The

default is

False

. Enabling

LCFEnable

will disable

MFSEnable

Multi-Frame Sequence bundling. This parameter appears only if

AutoPerfTuning

False

. Prevents (

True

) or allows (

False

) the

interleaving of frames in a sequence. The default is

False

. Enabling

MFSEnable

disables

LCFEnable

and

VIEnable

Virtual Interface (VI) preference routing. This parameter appears only if

AutoPerfTuning

False

. Enables (

True

) or disables (

False

) VI

preference routing. The default is

False

. Enabling

VIEnable

will

disable

MFSEnable

MSEnable

Management server enable. Enables (

True

) or disables (

False

)

management server on this port. The default is

True

NoClose

Loop circuit closure prevention. Enables (

True

) or disables (

False

) the

loop’s ability to remain in the open state indefinitely.

True

reduces the

amount of arbitration on a loop when there is only one device on the

loop. The default is

False

Table 33

Port configuration parameters (continued)

Parameter

Description

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands