HP StorageWorks SN6000 Command Line Interface Manual Download Page 137

Page: 137 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 137

restore

import

Restores configuration settings to the switch from a configuration backup file named

configdata

. You can create a backup file using the

config backup

command. Typically,

you would upload this backup file from a server using FTP.
The optional

import

operand imports the backup file from a remote server, prompting you for

an account name, server IP address or DNS host name, configuration file name on the server,

and a password if the server requires one. When the upload is complete, the switch restores the

configuration.
After the restore is complete, the switch automatically resets. See ”

Backing up and restoring a

switch configuration

” (page 46).

NOTE:

• If the restore process changes the IP address, use the

set setup system

command to

return the IP configuration to the values you want. If the IP address is unknown, you must

place the switch in maintenance mode and reset the network configuration to restore the

default IP address 10.0.0.1. For information about using maintenance mode, see the

StorageWorks SN6000 Fibre Channel Switch Installation and Reference Guide

• Configuration archive files created with the QuickTools or Enterprise Fabric Management

Suite Archive function are not compatible with the

config restore

command.

• The

configdata

backup file does not include the security group primary or secondary

secrets and therefore are not restored. Unless you edit the security database and

reconfigure the secrets, the switch will be isolated from the fabric.

save

[config_name]

Saves changes made during a configuration edit session in the configuration given by

[config_name]. If you omit [config_name], the value for [config_name] you chose for the most

recent

config edit

command is used. [config_name] can be up to 31 characters excluding #,

semicolon (;), and comma (,). The switch supports up to 10 configurations, including the default

configuration.

Notes

Changes you make to an active or inactive configuration can be saved, but will not take effect until

you activate that configuration.

Examples

The following shows an example of how to open and close a Config Edit session:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #> config edit

The config named default is being edited.

SN6000 FC Switch (admin-config) #> config cancel

Configuration mode will be canceled. Please confirm (y/n): [n] y

SN6000 FC Switch (admin) #> admin end

The following is an example of how to create a backup file (

configdata

) and download the file to

the workstation.

SN6000 FC Switch #> config backup

SN6000 FC Switch #> exit

#>ftp

symbolic_name or ip_address

user: images

password: images

ftp> bin

ftp> get configdata

ftp> quit

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands