HP StorageWorks SN6000 Command Line Interface Manual Download

Page: 180 / 330

180 Command Reference

reset

Description

Resets the switch configuration parameters. If you omit the operand, the default is

reset switch

Authority

Admin session

Syntax

reset

callhome

config

[config_name]

factory

ipsec

port [port_list]

radius

security

services

snmp

switch (default)

system

zoning

Operands

callhome

Resets the Call Home database configuration to its default values.

config

[config_name]

Resets the configuration given by [config_name] to the factory default values for switch, port, port

threshold alarm, and zoning configuration as described in

Table 17

through

Table 30

. If

[config_name] does not exist on the switch, a configuration with that name will be created. If you

omit [config_name], the active configuration is reset. You must activate the configuration for the

changes to take effect.

factory

Resets switch configuration, port configuration, port threshold alarm configuration, zoning

configuration, SNMP configuration, system configuration, security configuration, RADIUS

configuration, switch services configuration, zoning configuration, and Call Home configuration

to the factory default values as described in

Table 17

through

Table 30

. The switch configuration

is activated automatically.

NOTE:

Because this operand changes network parameters, the workstation could lose

communication with the switch and release the Admin session.
This operand does not affect installed license keys.

ipsec

Resets the IP security database configuration to its default values.

port [port_list]

Reinitializes one or more ports given by [port_list]. [port_list] can be a set of port numbers and

ranges delimited by spaces. For example,

0 2 10-15

specifies ports 0, 2, 10, 11, 12, 13, 14,

and 15.

radius

Resets the RADIUS configuration to the default values as described in

Table 22

security

Clears the security database and deactivates the active security set. The security configuration

value, autosave, and fabric binding remain unchanged.

services

Resets the switch services configuration to the default values as described in

Table 23

snmp

Resets the SNMP configuration settings to the factory default values. See

Table 21

for SNMP

configuration default values.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands