HP StorageWorks SN6000 Command Line Interface Manual Download Page 213

Page: 213 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 213

set setup radius

Description

Configures RADIUS servers on the switch.

Authority

Admin session

Syntax

set setup radius

common

server [server_number]

Operands

common

Prompts you in a line-by-line fashion to configure attributes that are common to all RADIUS

servers. To configure common and server-specific attributes, omit the operand.

Table 47

describes the common RADIUS server configuration attributes.

Table 47

Common RADIUS server configuration attributes

Attribute

Description

DeviceAuthOrder

Authenticator priority for devices:

•

Local

: Authenticate devices using only the local security database.

This is the default.

•

Radius

: Authenticate devices using only the security database on the

RADIUS server.

•

RadiusLocal

: Authenticate devices using the RADIUS server security

database first. If the RADIUS server is unavailable, then use the local

switch security database.

UserAuthOrder

Authenticator priority for user accounts:

•

Local

: Authenticate users using only the local security database. This

is the default.

•

Radius

: Authenticate users using only the security database on the

RADIUS server.

•

RadiusLocal

: Authenticate users using the RADIUS server security

database first. If the RADIUS server is unavailable, then use the local

switch security database.

TotalServers

Number of RADIUS servers to configure during this session. Setting

TotalServers to

disables all RADIUS authentication. The default is

Operands

server [server_number]

Prompts you in a line-by-line fashion to configure attributes for the RADIUS server given by

[server_number]. [server_number] is a positive integer. To configure common and specific

RADIUS server parameters, omit the operand.

Table 48

describes the server-specific RADIUS

server configuration attributes.

Table 48

Server-specific RADIUS server configuration attributes

Attribute

Description

ServerIPAddress

IP address (version 4 or 6) or DNS host name of the RADIUS server. The

default is

10.0.0.1

ServerUDPPort

User Datagram Protocol (UDP) port number on the RADIUS server. The

default is

1812

DeviceAuthServer

Enable (

True

) or disable (

False

) this server for device authentication.

The default is

False

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands