HP StorageWorks SN6000 Command Line Interface Manual Download Page 210

Page: 210 / 330

210 Command Reference

set port

Description

Sets port state and speed for the specified port temporarily until the next switch reset or new

configuration activation. This command also clears port counters.

Authority

Admin session

Syntax

set port clear

set port [port_number]

clear

speed [transmission_speed]

state [state]

Operands

[port_number]

Specifies the port. Ports are numbered beginning with 0.

clear

Clears the counters on all ports or the port given by [port_number].

speed [transmission_speed]

Specifies the port transmission speed.

Table 44

describes the transmission speed parameters.

Table 44

Transmission speed parameters

Parameter

Description

2Gb/s

The port speed is 2 Gb/s.

4Gb/s

The port speed is 4 Gb/s.

8Gb/s

The port speed is 8 Gb/s.

10Gb/s

The port speed is 10 Gb/s. This applies only to ports 20–23.

20Gb/s

The port speed is 20 Gb/s. This applies only to ports 20–23.

Auto

The port speed is automatically detected.

state [state]

Specifies the port administrative state.

Table 45

describes the port administrative state

parameters.

Table 45

Port administrative state parameters

Parameter

Description

Online

Activates and prepares the port to send data

Offline

Prevents the port from receiving signal and accepting a device login

Diagnostics

Prepares the port for testing and prevents the port from accepting a device

Down

Disables the port by removing power from the port lasers

Notes

QuickTools and Enterprise Fabric Management Suite override any temporary administrative state

changes that have been made using the Set Port State command. Therefore, to avoid unexpected

results, do not manage port administrative states with QuickTools or Enterprise Fabric Management

Suite and the CLI at the same time.

See also

show port

, page 261

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands