HP StorageWorks SN6000 Command Line Interface Manual Download Page 200

Page: 200 / 330

200 Command Reference

set config security portbinding

Description

Configures port binding.

Authority

Admin session and a Config Edit session

Syntax

set config security portbinding [port_number]

Operands

[port_number]

Initiates an editing session in which to change the port binding configuration for the port given by

[port_number]. The system displays each parameter one line at a time and prompts you for a value.

For each parameter, enter a new value or press

Enter

to accept the current value shown in brackets.

Enter

to end the editing session.

Table 35

describes the

set config security

portbinding

parameters.

Table 35

Port binding configuration parameters

Parameter

Description

PortBindingEnabled

Enables (

True

) or disables (

False

) port binding for the port

given by [port_number]. The default is

False

WWN

Worldwide port name for the port/device that is allowed to

connect to the port given by [port_number].

Examples

The following is an example of the

set config security portbinding

command:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) config edit

SN6000 FC Switch (admin-config) #> set config security portbinding 1

A list of attributes with formatting and current values will follow.

Enter a new value or simply press the ENTER key to accept the current
value.

If you wish to terminate this process before reaching the end of the list

press 'q' or 'Q' and the ENTER key to do so.

PortBindingEnabled (True / False)[False] true

WWN (N=None / WWN)[None ] 10:00:00:c0:dd:00:b9:f9

WWN (N=None / WWN)[None ] 10:00:00:c0:dd:00:b9:f8

WWN (N=None / WWN)[None ] n

Finished configuring attributes.

This configuration must be saved (see config save command) and

activated (see config activate command) before it can take effect.

To discard this configuration use the config cancel command.

See also

show config security portbinding

, page 239

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands