HP StorageWorks SN6000 Command Line Interface Manual Download Page 165

Page: 165 / 330

HP StorageWorks SN6000 Fibre Channel Switch Command Line Interface Guide 165

ipsec list

Description

Displays information about IP security associations and policies.

Authority

None

Syntax

ipsec list

active

association

[option]

configured

edited

policy

[option]

Operands

active

Displays a summary of active associations and policies. This is the default.

association

[option]

Displays the configuration for the associations given by [option]. If you omit [option], the

command displays the configuration of all active associations. [option] can be one of the

following:

[association]

Displays the configuration for the association given by [association].

active

Displays the configuration for all active associations.

configured

Displays the configuration for all user-defined associations.

edited

Displays the configuration for all associations that have been modified, but not saved.

configured

Displays a summary of the user-defined associations and policies.

edited

Displays a summary of the associations and policies that have been modified, but not saved.

policy

[option]

Displays the configuration for the policies given by [option]. If you omit [option], the command

displays the configuration of all active policies. [option] can be one of the following:

[policy]

Displays the configuration for the policy given by [policy].

active

Displays the configuration for all active policies.

configured

Displays the configuration for all user-defined policies.

edited

Displays the configuration for all policies that have been modified, but not saved.

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands