HP StorageWorks SN6000 Command Line Interface Manual Download Page 126

Page: 126 / 330

126 Command Reference

admin

Description

Opens and closes an Admin session. The Admin session provides access to commands that change

the fabric and switch configurations. Only one Admin session can be open on the switch at any time.

An inactive Admin session will time out after a specified period of time, which is changed using the

set setup system

command.

Authority

User account with Admin authority

Syntax

admin

start

begin

end

stop

cancel

Operands

start

begin)

Opens the Admin session

end

stop

Closes the Admin session. The

hardreset

hotreset

quit

shutdown

, and

reset switch

commands will also end an Admin session.

cancel

Terminates an Admin session opened by another user. Use this operand with care because it

terminates the Admin session without warning the other user and without saving pending

changes.

Notes

Closing a Telnet window during an Admin session does not release the session. In this case, you

must either wait for the Admin session to time out, or use the

admin cancel

command.

Examples

The following example shows how to open and close an Admin session:

SN6000 FC Switch #> admin start

SN6000 FC Switch (admin) #>

SN6000 FC Switch (admin) #> admin end

See also

set setup system

, page 222

Summary of Contents for StorageWorks SN6000











































































































































































































































































































































Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands

HP StorageWorks SN6000, Command Line Interface Manual

Search results

Summary of Contents for StorageWorks SN6000

Reviews:

Related manuals for StorageWorks SN6000

Brands by name

Popular brands