manualshive.com logo in svg

HP StorageWorks 2/140 - Director Switch, Product Manager Manual

The HP StorageWorks 2/140 - Director Switch is a versatile storage solution that offers high-performance and scalability. Need help getting started? You can easily access the comprehensive user manual for free on manualshive.com. Get step-by-step instructions on installation, maintenance, and troubleshooting, ensuring optimal usage of this outstanding storage solution.

Share
Download
background image

director product manager user guide

A–27

Information and Error Messages

The data collection 
process has been 
aborted.

The user aborted the 
data collection 
procedure.

Verify the data collection 
procedure is to be aborted, 
then click OK to continue.

The default zone 
must be disabled to 
configure. 

The message 
displays when the 
user attempts to 
change the operating 
mode to the open 
fabric mode and the 
default zone is 
enabled.

Disable the default zone and 
repeat the operation.

The director did not 
accept the request.

The director cannot 
perform the 
requested action.

Retry the operation. If the 
condition persists, contact the 
next level of support.

The director did not 
respond in the time 
allowed.

While waiting to 
perform a requested 
action, the director 
timed out.

Retry the operation. If the 
condition persists, contact the 
next level of support.

The director is busy 
saving maintenance 
information.

The director cannot 
perform the 
requested action 
because it is busy 
saving maintenance 
information.

Retry the operation later. If 
the condition persists, contact 
the next level of support.

The director must 
be offline to 
configure.

A configuration 
changed was 
attempted for a 
configuration 
requiring offline 
changes.

Take the appropriate actions 
to set the director offline 
before attempting the 
configuration change.

The Ethernet link 
dropped.

The Ethernet 
connection between 
the HAFM server and 
the director is down 
or unavailable.

Establish and verify the 
network connection.

Table A–1:  Product Manager Messages  (Continued)

Message Description

Action

Summary of Contents for StorageWorks 2/140 - Director Switch





















































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2/140 - Director Switch

TANDBERG Codian Remote Management API Reference Manual preview
Codian Remote Management API
Brand: TANDBERG Pages: 66
Alphasmart AS 3000 Installation And User Manual preview
AS 3000
Brand: Alphasmart Pages: 4
KAPERSKY ANTI-VIRUS 5.5 - FOR NOVELL NETWARE Administrator'S Manual preview
ANTI-VIRUS 5.5 - FOR NOVELL NETWARE
Brand: KAPERSKY Pages: 134
MACROMEDIA COLDFUSION 5 - INSTALING AND CONFIGURING... Manual preview
COLDFUSION 5 - INSTALING AND CONFIGURING...
Brand: MACROMEDIA Pages: 160
Alpha Moisture Systems SADPmini Logger Instruction Manual preview
SADPmini Logger
Brand: Alpha Moisture Systems Pages: 14
Acer ASM 7 Faq preview
ASM 7
Brand: Acer Pages: 32
Acer Altos RAIDWatch Manual preview
Altos RAIDWatch
Brand: Acer Pages: 212
M-Audio GForce M-Tron Pro Quick Start Manual preview
GForce M-Tron Pro
Brand: M-Audio Pages: 4
M-Audio DRUM AND BASS RIG (German) Kurzanleitung preview
DRUM AND BASS RIG
Brand: M-Audio Pages: 3
AppsDaily C2 User Manual preview
C2
Brand: AppsDaily Pages: 38
KAPERSKY ANTI-VIRUS 5.7 - FOR LINUX FILE SERVER Administrator'S Manual preview
ANTI-VIRUS 5.7 - FOR LINUX FILE SERVER
Brand: KAPERSKY Pages: 104
Waves The King's User Manual preview
The King's
Brand: Waves Pages: 16
Brocade Communications Systems 8 Reference Manual preview
8
Brand: Brocade Communications Systems Pages: 382
FARONICS WINSELECT ENTERPRISE Manual preview
WINSELECT ENTERPRISE
Brand: FARONICS Pages: 39
Lenovo ThinkCentre A61e Specifications preview
ThinkCentre A61e
Brand: Lenovo Pages: 4
Lenovo ThinkCentre A62 Reference Manual preview
ThinkCentre A62
Brand: Lenovo Pages: 134
Lenovo ThinkCentre A63 Hardware Maintenance Manual preview
ThinkCentre A63
Brand: Lenovo Pages: 216
Lenovo ThinkCentre A62 Brochure preview
ThinkCentre A62
Brand: Lenovo Pages: 4

Brands by name

Popular brands

Load more brands