manualshive.com logo in svg

HP StorageWorks 2/140 - Director Switch, Product Manager Manual

The HP StorageWorks 2/140 - Director Switch is a versatile storage solution that offers high-performance and scalability. Need help getting started? You can easily access the comprehensive user manual for free on manualshive.com. Get step-by-step instructions on installation, maintenance, and troubleshooting, ensuring optimal usage of this outstanding storage solution.

Share
Download
background image

director product manager user guide

A–25

Information and Error Messages

Product Manager 
error < error 
number 5001 or 
5002 >.

The Product 
Manager application 
encountered an 
internal error (5001 
or 5002) and cannot 
continue operation.

Contact the next level of 
support to report the problem.

Product Manager 
instance is 
currently open. 

A Product Manager 
window is currently 
open.

Informational message only.

R_A_TOV must be 
greater than 
E_D_TOV.

R_A_TOV must be 
greater than 
E_D_TOV.

Change one of the values so 
that R_A_TOV is greater than 
E_D_TOV

Resource is 
unavailable.

The specified 
operation cannot be 
performed because 
the product is 
unavailable.

Verify that the Ethernet 
connection between the 
HAFM server and the director 
is up or available.

SANtegrity Feature 
not installed. Please 
contact your sales 
representative.

The user selected 
Switch Binding from 
the Configure menu, 
but the optional 
SANtegrity feature is 
not installed.

Install the SANtegrity key 
through the Configure 
Feature Key dialog box 
before using Switch Binding 
features.

Send firmware 
failed.

A firmware download 
operation failed.

Retry the firmware download 
operation. If the problem 
persists, contact the next level 
of support.

SNMP trap address 
not defined.

If an SNMP 
community name is 
defined, a 
corresponding SNMP 
trap recipient address 
must also be defined.

Enter a corresponding SNMP 
trap recipient address.

Table A–1:  Product Manager Messages  (Continued)

Message Description

Action

Summary of Contents for StorageWorks 2/140 - Director Switch





















































































































































































































































Reviews:

No comments

Related manuals for StorageWorks 2/140 - Director Switch

Garmin GPSMAP GPSMAP 196 Getting Started preview
GPSMAP GPSMAP 196
Brand: Garmin Pages: 4
Garmin MapSource Owner'S Manual preview
MapSource
Brand: Garmin Pages: 2
TANDBERG MPS API Interface D13639 User Manual preview
MPS API Interface D13639
Brand: TANDBERG Pages: 84
NETGEAR GS110TP - ProSafe Gigabit Smart Switch Installation Manual preview
GS110TP - ProSafe Gigabit Smart Switch
Brand: NETGEAR Pages: 2
Patton electronics SmartNode Series Software Configuration Manual preview
SmartNode Series
Brand: Patton electronics Pages: 655
Minolta DIMAGE VIEWER 2.1 Instruction Manual preview
DIMAGE VIEWER 2.1
Brand: Minolta Pages: 84
Sony MSSW-IC2 User Manual preview
MSSW-IC2
Brand: Sony Pages: 2
Sony ICDBM1 - Memory Stick Media Digital Voice Recorder Supplementary Manual preview
ICDBM1 - Memory Stick Media Digital Voice Recorder
Brand: Sony Pages: 1
Sony ICDBM1 - Memory Stick Media Digital Voice Recorder Specifications preview
ICDBM1 - Memory Stick Media Digital Voice Recorder
Brand: Sony Pages: 2
Sony ICD-BP150 - Ic Recorder Specifications preview
ICD-BP150 - Ic Recorder
Brand: Sony Pages: 2
Sony D-NS921F - Portable Cd Player Specifications preview
D-NS921F - Portable Cd Player
Brand: Sony Pages: 2
Sony MS Export User Manual preview
MS Export
Brand: Sony Pages: 9
Sony Music Box v.2.1.0 Manual preview
Music Box v.2.1.0
Brand: Sony Pages: 12
Sony Memory Stick Autorun v1.3 Operating Instructions Manual preview
Memory Stick Autorun v1.3
Brand: Sony Pages: 24
Sony ICD-R100 Operating Instructions (primary manual) Service Manual preview
ICD-R100 Operating Instructions (primary manual)
Brand: Sony Pages: 22
Sony ICD-BP100 - Ic Recorder Service Manual preview
ICD-BP100 - Ic Recorder
Brand: Sony Pages: 32
Sony Image Converter 2 Plus Operating Instructions Manual preview
Image Converter 2 Plus
Brand: Sony Pages: 40
Sony Emma User Manual preview
Emma
Brand: Sony Pages: 34

Brands by name

Popular brands

Load more brands