Cmsemicon BAT32G1 9 Series User Manual Download

Page: 350 / 1149

BAT32G1x9 user manual | Chapter 10 Timer M

www.mcu.com.cn

350 / 1149

Rev.1.02

10.3.16

Timer M interrupt enable register i (TMIERi) (i= 0, 1).

Figure 10-28 the format of Timer M interrupt enable register i (TMIERi) (i=0, 1).

Address: 0x40042A74

(TMIER0),

0x40042A84

(TMIER1) after reset:

00HR/W

symbol

TMIERi

OVIE

Allowed overflow/underflow interrupts

Interrupts due to OVF bits and UDF bits (OVI) are prohibited.

Interrupts due to OVF bits and UDF bits (OVI) are allowed.

IMIED

Input capture/comparison matching interrupts allow

Interrupts (IMID) due to IMFD bits are prohibited.

Interrupts (IMIDs) due to IMFD bits are allowed.

IMIEC

Input capture/compare matching interrupts allow

Interrupts due to IMFC bits (IMIC) are prohibited.

Interrupts due to IMFC bits (IMCs) are allowed.

IMIEB

Input capture/compare matching interrupts allow

Interrupts due to IMFB bits (IMIB) are prohibited.

Interrupts due to IMFB bits (IMIB) are allowed.

IMIEA

Input capture/compare matching interrupts allow

Interrupts due to IMFA bits (IMIA) are prohibited.

Interrupts due to IMFA bits (IMIA) are allowed.

OLife

InIED

IMIEC

InIEB

IMIE EA

Summary of Contents for BAT32G1 9 Series






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for BAT32G1 9 Series

Reviews:

Related manuals for BAT32G1 9 Series

Brands by name

Popular brands

Cmsemicon BAT32G1 9 Series, User Manual

Search results

Summary of Contents for BAT32G1 9 Series

Reviews:

Related manuals for BAT32G1 9 Series

Brands by name

Popular brands