MENu ADDRESS
SETTINGS DESCRIPTION
INFORMATION
PRODuCT
Control Panel >
Network >
LAN Settings >
H.323 Settings >
ADVANCED H.323 SETTINGS
NAT
NAT support in the videoconferencing system enables proper exchange of audio/video data when connected
to an external videoconferencing system (when the IP traffic goes through a NAT router).
OFF:
The system will signal the real IP Address.
ON:
The system will signal the configured “NAT Address” in place of its own IP-address within Q.931
and H.245. When NAT is On, the NAT Server Address will be shown in the startup-menu as:
My IP
Address: 10.0.2.1
AuTO:
The system will try to determine if the “NAT Address” or the real IP-address should be used within signaling.
This is done to make it possible to place calls to endpoints on the LAN as well as endpoints on the WAN.
Note! The Advanced H.323 Settings only have effect if they
are supported by your IP infrastructure.
All
Control Panel >
Network >
LAN Settings >
H.323 Settings >
ADVANCED H.323 SETTINGS
NAT ADDRESS
This must be the external/global IP-address to the router with NAT support. Packets sent to the router
will then be routed to the system. In the router, the following ports must be routed to the system’s IP-
address:
•
Port 1720
•
Port 5555-5574
•
Port 2326-2485
Note! The Advanced H.323 Settings only have effect if they
are supported by your IP infrastructure.
All
Control Panel >
Network >
LAN Settings >
H.323 Settings >
ADVANCED H.323 SETTINGS
RSVP
AuTO:
Resource Reservation Protocol enables the system to request the optimum amount of bandwidth
for the duration of an IP video conference.
OFF:
Resource Reservation Protocol is switched Off.
Note! The Advanced H.323 Settings only have effect if they
are supported by your IP infrastructure.
All
Control Panel >
Network >
LAN Settings >
H.323 Settings >
ADVANCED H.323 SETTINGS
H.323 PORTS
STATIC:
When selecting static H.323 ports for TCP connections the ports 5555 - 5574 will be used for
Q.931 and H.245 respectively.
DyNAMIC:
The system will allocate which ports to use when opening a TCP connection. The reason for
doing this is to avoid using the same ports for subsequent calls, as some firewalls consider this as
a sign of attack. When Dynamic is selected, the H.323 ports used are from 11000 to 65535. Once
65535 is reached they restart again at 11000.
Note! The Advanced H.323 Settings only have effect if they
are supported by your IP infrastructure.
Save and Restart
The system needs to be restarted after changing the H.323
ports.
All
Control Panel >
Network >
LAN Settings >
SIP SETTINGS
SIP MODE
SIP - Session Initiation Protocol. SIP is one of the leading signaling protocols for Voice over IP.
ON:
Setting the SIP mode to On will enable the system for incoming and outgoing SIP calls.
OFF:
Setting the SIP mode to Off will disable incoming and outgoing SIP calls from the system.
Save and Restart
The system need to be restarted if SIP mode is turned On.
Turning SIP Off will make the video system reject outgoing
and incoming calls.
All
Control Panel >
Network >
LAN Settings >
SIP SETTINGS
DISPLAy NAME
The Display Name of the SIP Address (URI) is usually a full name or system name.
Examples:
“Alice Wonderland”, “System 01”
All
77
Cisco TelePresence MXP Series
Administrator guide
D14791.01 MXP Series Administrator Guide F90, August
2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
www.cisco.com
Contents
Contact us
Introduction
The menu structure
The settings library
Getting started
Appendices
The settings library
