MENu ADDRESS
SETTINGS DESCRIPTION
INFORMATION
PRODuCT
Control Panel >
Network >
ISDN, External, Leased E1/T1 >
ISDN-PRI Settings >
CHANNEL HUNTING
CHANNEL HuNTING
MAX CHANNELS:
Set the maximum number of channels the system may use at any given time. Max
Channels may be used for PRIs that are provisioned for a lower number of channels.
LOW CHANNEL:
Set the lowest numbered B-channel that may be used by the system when
selecting channels for outgoing calls. Low Channel may be used for PRIs provisioned with specific
requirements for B-channel usage.
HIGH CHANNEL:
Set the highest numbered B-channel that may be used by the system when
selecting channels for outgoing calls. High Channel may be used for PRIs provisioned with specific
requirements for B-channel usage
SEARCH:
Specifies where the system will start searching for available B-channels for outgoing calls.
Search may be used for PRIs provisioned with specific requirements for B-channel usage.
HIGH:
The system will start searching for available B-channels at the specified High Channel
number.
LOW:
The system will start searching for available B-channels at the specified Low Channel number.
The system will start searching for available B-channels at
channel 31, since Search is set to High and High Channel is
set to 31.
The system will search for channels down to channel no 1,
since Low Channel is set to 1.
Furthermore; if the user tries to make a 31 channel call,
the call will be established with 30 channels, since Max
Channels is set to 30.
All with
ISDN-PRI
Control Panel >
Network >
ISDN, External, Leased E1/T1 >
ISDN-PRI Settings >
LINE SETTINGS
T1 CABLE LENGTH 1
Configures the ISDN-PRI Line Settings.
Specify the distance (0-133 ft) of the CSU connected to the E1/T1 Port 1 on Codec 1.
CSU - Channel Service Unit
All with
ISDN-PRI
Control Panel >
Network >
ISDN, External, Leased E1/T1 >
ISDN-PRI Settings >
LINE SETTINGS
E1 CRC-4
E1 CRC-4 is used for most E1-PRI configurations.
ON:
Select On if E1 CRC-4 is supported by your E1 network equipment.
OFF:
Select Off if E1 CRC-4 is not supported by your E1 network equipment.
CRC - Cyclic Redundancy Check
All with
ISDN-PRI
Control Panel >
Network >
ISDN, External, Leased E1/T1 >
ISDN-PRI Settings >
ADVANCED ISDN SETTINGS
SuB ADDRESS
Using a Sub Address enables you to connect up to eight ISDN terminals to the same ISDN telephone
number and line. The terminals are addressed by using different sub addresses.
To call a terminal with a sub address, separate the ISDN telephone number and the sub address with a
‘*’.
Example:
12345678*2
(up to four digit sub addresses are possible)
This service is dependent on your service provider and has
limited access on some ISDN networks.
All with
ISDN-PRI
Control Panel >
Network >
ISDN, External, Leased E1/T1 >
ISDN-PRI Settings >
ADVANCED ISDN SETTINGS
VALIDATE NuMBERS (MSN)
The use of MSN (Multiple Subscriber Number) enables you to attach different ISDN terminals, with
different numbers, to the same physical ISDN telephone line. If available this service can be ordered
from your telephone company.
ON:
When set to On only calls to the numbers specified in the Line Setup menus will be answered.
OFF:
When set to Off all calls will be answered.
MSN - Multiple Subscriber Number
All with
ISDN-PRI
69
Cisco TelePresence MXP Series
Administrator guide
D14791.01 MXP Series Administrator Guide F90, August
2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
www.cisco.com
Contents
Contact us
Introduction
The menu structure
The settings library
Getting started
Appendices
The settings library
