MENu ADDRESS
SETTINGS DESCRIPTION
INFORMATION
PRODuCT
Control Panel >
Audio >
AUDIO OUTPUTS
AuDIO MODuLE
This menu item is only available if the audio module is unidentified, otherwise it is hidden.
If the system has automatically detected Digital NAM (DNAM - Digital Natural Audio Module), then this
menu item will not be available.
If the Audio Module is unidentified you will be allowed to select an Audio Module according to the type of
Audio Module installed.
The audio module options are:
•
NAMII-T6000
•
NAMII-T8000
•
Digital NAM
•
None
6000
3000
95/75
Control Panel >
Audio >
Audio Outputs >
LEVEL SETTINGS
OuTPuT LEVEL SETTINGS - OuT 1-3
Applies to: Cisco TelePresence Codec 6000 MXP
Adjust the audio output levels according to the parameters of the external audio equipment connected.
These levels should only be adjusted when installing new audio equipment. The default settings are
correct for the TANDBERG Digital Natural Audio Module (DNAM) and for most consumer electronics
devices (televisions, VCRs, etc.). Use the volume keys on the remote control to adjust the level of output
1 (the speaker output). The volume control has no effect on other outputs.
OuT1:
is intended for connection to TANDBERG Digital Natural Audio Module, televisions or audio
amplifiers. Set the maximum level. The nominal level is -10,0 dBu.
OuT2 (AuX):
is intended for connection to audio recording equipment or to a telephone add-on hybrid.
The signal is a mix of audio from both the far end and local end (not from Audio in 5).
Set the maximum level. The nominal level is -10,0 dBu.
OuT3 (VCR):
is intended for connection to a VCR or other recording equipment. The signal is a mix of
audio from far end and local end (not from Audio in 6).
Set the maximum level. The nominal level is -10,0 dBu.
See the
Interfaces
in the
Peripheral Equipment
section for
more information on this topic for your product.
When no audio module is detected, audio outputs can be:
Out 2 for VCR Left
Out 3 for VCR Right.
6000
Control Panel >
Audio >
Audio Outputs >
LEVEL SETTINGS
OuTPuT LEVEL SETTINGS - OuT 1-2*
Applies to: Cisco TelePresence Codec 3000 MXP, 990/880/770 MXP, 550 MXP, Edge 95/75 MXP
Adjust the audio output levels according to the parameters of the external audio equipment connected.
These levels should only be adjusted when installing new audio equipment. The default settings are
correct for the TANDBERG Digital Natural Audio module and for most consumer electronics devices
(televisions, VCRs, etc.). The volume keys on the remote control adjust the level of output 1 (the speaker
output). The volume control has no effect on other outputs..
OuT1:
is intended for connection to televisions or audio amplifiers.
Set the maximum level. The nominal level is -10,0 dBu.
OuT2 (AuX):
is intended for connection to a VCR or other recording equipment. The signal is a mix of
audio from far end and local end (except VCR in).
Set the maximum level. The nominal level is -10,0 dBu.
See the
Interfaces
in the
Peripheral Equipment
section for
more information on this topic for your product.
When no audio module is detected, audio outputs can be:
Out 1 for VCR Left
Out 2 for VCR Right.
* TANDBERG 550 MXP has one Audio Output (see Out1).
3000
95/75
59
Cisco TelePresence MXP Series
Administrator guide
D14791.01 MXP Series Administrator Guide F90, August
2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
www.cisco.com
Contents
Contact us
Introduction
The menu structure
The settings library
Getting started
Appendices
The settings library
