5 Video Inputs
•
1 (one) 9 Pin DSUB is used for connecting the PrecisionHD
Camera.
•
1 video inputs supporting S-Video through Mini-DIN
connectors.
•
2 video inputs supporting composite signals through RCA
connectors.
•
1 VGA/DVI-I (DVI = Digital Visual Interface, I = Integrated
Digital & Analog) input, analog or digital.
Levels
Composite: 1 Vpp, 75 ohm
S-Video (Y/C):
Y: 1 Vpp, 75 ohm
C (PAL): 0.3 Vpp, 75 ohm
C (NTSC): 0.28 Vpp, 75 ohm
The system will automatically adapt to a PAL or NTSC input.
VGA formats supported on DVI-I in
SVGA (800x600) 60Hz, 72Hz, 75Hz, 85Hz
XGA (1024x768) 60 Hz, 70Hz, 75Hz
SXGA (1280x1024) 60Hz
HD720p (1280x720) 50 Hz, 60 Hz
WXGA (1280x768, 1280x800, 1360x768, 1366x768 (@60 Hz))
Read More
Read more about the DVI (Digital Visual Interface) and DVI Cables
in the beginning of the Peripheral Equipment section.
Go to
The Digital Visual Interface (DVI)
Go to
DVI Cables - The VGA to DVI
Go to
DVI Cables - The VGA to DVI-A
4 Video Outputs
•
1 S-Video output, Mini-DIN connector.
•
2 composite video outputs, RCA connectors.
•
1 VGA/DVI-I (DVI = Digital Visual Interface, I = Integrated
Digital & Analog) output, analog or digital.
The first Mini-DIN connector and the first RCA connector provide
main video (incoming/outgoing video and menus). The other
connector provides selfview/still image/DuoVideo. The outputs
are always active. The format of the output will be either PAL or
NTSC depending on your country’s standard video format. The
VGA/DVI output provides either main monitor video or second
monitor video depending on menu configuration.
Levels
Composite: 1 Vpp, 75 ohm
S-Video (Y/C):
Y: 1 Vpp, 75 ohm
C (PAL): 0.3 Vpp, 75 ohm
C (NTSC): 0.28 Vpp, 75 ohm
VGA formats supported on DVI-I out
SVGA (800x600) 75Hz
XGA (1024x768) 60Hz
WXGA (1280x768) 60Hz
HD720p (1280x720) 50 Hz, 60 Hz
Read more
Read more about the DVI (Digital Visual Interface) and DVI Cables
in the beginning of the Peripheral Equipment section.
Go to
The Digital Visual Interface (DVI)
Go to
DVI Cables - The VGA to DVI
Go to
DVI Cables - The VGA to DVI-A
4 Audio Inputs
•
2 microphone inputs (balanced, 24V phantom powered) via
XLR connectors.
•
2 audio inputs (line level) via RCA connectors.
All audio inputs are active by default. For further information,
refer to the description of
Audio
in the Control Panel Library.
Audio Input Connector Specification
Connector Label
Microphone(s)
Audio Input(s)
Signal type
Balanced
Unbalanced
Copnnector (codec)
XLR-F, pin 1-gnd,
pin 2 hot, pin
3-cold/neutral
Female RCA/
phono, sleeve-
ground, centre-
signal
Input Impedance
2400 ohms (pin
2-3)
10K ohms
Max input level when
set to minimum input
level
83 mVpp
15.5 Vpp
Max input level when
set to maximum input
level
6.2 mVpp
1.2 Vpp
Range, menu
adjustable input gain
22.5 dB (16 steps
of 1.5 dB)
22.5 dB (16 steps
of 1.5 dB)
Phantom power
voltage
24 V +/- 5%
-
Phantom power
resistor, pin 2
1200 ohms
-
Phantom power
resistor, pin 2
1200 ohms
-
Max phantom power
current pr mic
12 mA
-
Edge 95/75 MXP Interfaces and sockets,
cont...
Video input/output and Audio input
119
Cisco TelePresence MXP Series
Administrator guide
D14791.01 MXP Series Administrator Guide F90, August
2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
www.cisco.com
Contents
Contact us
Introduction
The menu structure
The settings library
Getting started
Appendices
Appendices
