MENu ADDRESS
SETTINGS DESCRIPTION
INFORMATION
PRODuCT
Control Panel >
Audio >
AUDIO OUTPUTS
AuDIO OuT 1-3
Applies to: Cisco TelePresence Codec 6000 MXP
OuT1:
is intended for connection to TANDBERG Digital Natural Audio Module, televisions or audio
amplifiers.
OuT2 (AuX):
is intended for connection to audio recording equipment or to a telephone add-on hybrid.
The signal is a mix of audio from both the far end and local end (not from Audio in 5).
If an output is Off, no audio will be sent to that output.
Do not connect Out2 (AUX) to a loudspeaker placed in the same room as the microphones
connected to the system. This will cause “howling” and possible damage to the speaker system.
OuT3 (VCR):
is intended for connection to a VCR or other recording equipment. The signal is a mix of
audio from far end and local end (not from Audio in 6). If an output is Off, no audio will be sent to that
output. Do not connect Out3 (VCR) to a loudspeaker placed in the same room as the microphones
connected to the system. This will cause “howling” and possible damage to the speaker system.
NOTE!
The Audio Out 2 or Audio Out 3 should never be
connected to a loudspeaker placed in the same room as
the microphones connected to the system. This will cause
“howling” and possible damage to the speaker system.
The different system can have different numbers of Audio
Inputs. See
Interfaces
in the
Peripheral Equipment
section
for more information on this topic for your product.
When no audio module is detected, audio outputs can be:
Out 2 for VCR Left
Out 3 for VCR Right.
6000
Control Panel >
Audio >
AUDIO OUTPUTS
AuDIO OuT 1-2*
Applies to: Cisco TelePresence Codec 3000 MXP, 990/880/770 MXP, 550 MXP, Edge 95/75 MXP
OuT1:
is intended for connection to televisions or audio amplifiers.
OuT2 (AuX):
is intended for connection to a VCR or other recording equipment. The signal is a mix of
audio from far end and local end (except VCR in).
NOTE!
The Audio Out 2 should never be connected to a
loudspeaker placed in the same room as the microphones
connected to the system. This will cause “howling” and
possible damage to the speaker system. If an Output is set
to Off, no audio will be sent to that output.
When no audio module is detected, audio outputs can be:
Out 1 for VCR Left
Out 2 for VCR Right.
* TANDBERG 550 MXP has one Audio Output (see Out1)
3000
95/75
Control Panel >
Audio >
AUDIO OUTPUTS
OuT 1 MODE
Set the mode for the Audio Out 1. The default mode is Auto.
ANALOG:
Setting the Out 1 Mode to Analog will override the auto-detected mode.
SPDIF (DIGITAL):
Setting the Out 1 Mode to SPDIF (Digital) will override the auto-detected mode.
AuTO:
If Out 1 Mode is set to Auto, the system will select
Analog
or
SPDIF
(Digital) mode dependent
on the detected Audio Module. If a TANDBERG Digital NAM is detected the SPDIF mode will be
selected, otherwise analog mode will be selected.
See
Stereo Settings
for additional information.
•
When Analog Mode is selected and the Stereo Speakers set to On, this will provide a stereo
loudspeaker signal on Audio out 1 and 2.
•
When SPDIF Mode is selected you are can receive stereo through Audio Out 1 independent of the
Stereo I/O Mode setting.
•
If both Stereo I/O Mode and Stereo Speakers are set to Off, the output response will be a mono
loudspeaker signal on Audio Out 1, AUX on Audio Out 2 and VCR on Audio Out 3 regardless on the
Audio Out 1 Mode setting.
See
Interfaces
in the
Peripheral Equipment
section for more
information on this topic for your product.
SPDIF - Sony/Philips Digital Interface
6000
3000
95/75
58
Cisco TelePresence MXP Series
Administrator guide
D14791.01 MXP Series Administrator Guide F90, August
2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
www.cisco.com
Contents
Contact us
Introduction
The menu structure
The settings library
Getting started
Appendices
The settings library
