manualshive.com logo in svg

Bay Networks 5391, Manual, Page: 245 / 351

Share
Download
Bay Networks 5391 Manual Download Page 245

A-55

Appendix A    RAC Parameters

Managing Remote Access Concentrators Using Annex Manager

lat_multicast_timer

defines the number of seconds that can elapse between service announcement
transmissions for the LAT protocol.

lat_sys_location

supplies host location or identification information for the LAT protocol.

lat_queue_max

limits the number of HIC (Host Initiated Connection) requests that a RAC can
queue.

latb_enable

allows a RAC to decode the LAT host data-b packets, which change
asynchronous port parameters. Refer to your LAT host documentation for details.

 If you enter

enabled

 and the LAT host sends a data-b slot message

requesting that flow control (XON/XOFF) be turned off, the RAC
turns off flow control and passes XON/XOFF characters to the host.
This scenario can adversely affect XON/XOFF and the terminal
cursor keys.

Type

RAC

Values

10 through 180 seconds

Default

30 seconds

Lists

RAC Only, LAT

Type

RAC

Values

0 to 32 characters

Default

“ “

Lists

RAC Only, LAT

Type

RAC

Values

1 to 255

Default

4

Lists

RAC Only, LAT

Type

Async

Values

enabled or disabled

Default

disabled

Lists

Async Ports, LAT

Summary of Contents for 5391
































































































































































































































































































































































Reviews:

No comments