Bay Networks 5391 Manual Download Page 117

Page: 117 / 351

4-43

Chapter 4 Setting Up RACs

Managing Remote Access Concentrators Using Annex Manager

Remote Address

Remote addressing is not available from the Setup menu for the 5393/
6300, 5399, and 8000. For these devices use the

Remote Addressing

box in

the

PPP Dial Access

window. See The PPP Dial Access Window on page

4-39 for instructions.

To configure RACs for remote addressing:

Create a RAC list and select the RACs you want to configure
(page 2-1).

In the

Main

window, select

Remote Address

from the

Setup

field at

the top of the window or click

Setup

and then select

Remote

Address

The

Remote Address

window appears (

Figure 4-14

). This window

is described in Remote Address Window on page 4-44.

Figure 4-14. Remote Address Window

Enter the

First Remote Address

and

Subnet Mask

address as

required. Annex Manager fills in the

Last Remote Address

field.

ARNING

Summary of Contents for 5391
































































































































































































































































































































































Search results

Summary of Contents for 5391

Reviews:

Bay Networks 5391, Manual, Page: 117 / 351

Search results

Summary of Contents for 5391

Reviews: