Bay Networks 5391 Manual Download Page 140

Page: 140 / 351

Managing Remote Access Concentrators Using Annex Manager

Chapter 5 Booting and Resetting RACs

5-10

•

All Printer Ports

resets the parallel printer ports.

•

All Virtual Ports

resets the virtual connections.

•

All T1 DS1 Ports (Hard)

resets the T1 engine and terminates the

T1 Drop/Insert interface and modem sessions

•

All T1DS1 Ports (Soft)

resets parameters and disrupts service only

on DS0 channels that were changed.

•

All ESF Counters

resets all T1 engine statistics.

•

All Interfaces

resets the interface parameters.

•

All Internal Modems

resets entries for internal modems only.

•

Individual Ports

resets only the port type you enter in the option

button below the

Reset Option

box and the port numbers you

enter in the adjacent field.

•

Individual Internal Modems

resets one or more internal modems

you enter in the option button below the

Reset Option

box and

the modem numbers you enter in the adjacent field.

•

Dialout

resets entries used for dialing out from a UNIX host to a

remote node over a port in slave mode.

•

LAT

resets LAT (Local Area Transport) parameters. When you

use this option, existing connections keep their current values:
new parameter values apply only to LAT connections
established after using

Reset

•

Macros

resets macros after you customize them in the RAC

configuration file.

•

Message of the Day

resets the file for the message that appears

when you establish a connection to a RAC.

•

External Modem

resets modem entries for external modems only.

•

PRI Line

resets a PRI line for an ISDN Primary Rate RAC.

•

PRI Sessions

reloads session parameter blocks in the

configuration file for an ISDN Primary Rate RAC session.

•

Name Server

resets the parameters and host table that enable a

RAC to translate addresses to names.

•

Security

resets security parameters.

Summary of Contents for 5391
































































































































































































































































































































































Search results

Summary of Contents for 5391

Reviews:

Bay Networks 5391, Manual, Page: 140 / 351

Search results

Summary of Contents for 5391

Reviews: