Home
/
Bay Networks
/
5391
/
Manual

Bay Networks 5391, Manual, Page: 188 / 351

Share

Page: 188 / 351

Bay Networks 5391 Manual Download Page 188

Managing Remote Access Concentrators Using Annex Manager

Chapter 9 Configuring SNMP Traps

9-2

The SNMP Settings Window

The

SNMP Settings

window displays information in the

SNMP Settings

box.

Check the buttons in this window to set thresholds for SNMP traps. The
default value is 0 (disabled). When you click the

Check

button of a trap

to enable it, the threshold value in the corresponding field is set to the
number 1. You can leave the threshold at one or set a higher threshold
value for which you want the trap to be enabled.

Select:

•

Call Begin

to generate a trap when an incoming call is

detected or an outbound call is generated by the RAC.

•

Call End

to generate a trap when a call terminates.

•

Unexpected Call disconnect

to generate a trap when a call

disconnects unexpectedly.

•

Forced Call Disconnect

to generate a trap when a call is

disconnected.

•

ESF errors

(Errored Second Format errors) to generate

a trap on ESF errors.

•

Loss of Frame Count

to generate a trap on loss of frame

count.

•

Unavailable seconds

to generate a trap on detection of

unavailable seconds.

•

Frame Errors

to generate a trap on detection of frame

errors.

•

Errored Seconds

to generate a trap on detection of

errored seconds.

•

CRC6 Errors

to generate a trap on detection of CRC6

errors.

•

Severely Errored Seconds

to generate a trap on detection

of severely errored seconds.

«
...
186
187
188
189
190
...
»

Summary of Contents for 5391
































































































































































































































































































































































Reviews:

No comments