Baumuller BUS 6-T Series Technical Description And Operations Manual Download Page 113

Page: 113 / 119

Status messages

Maintenance

Controller BUS 6 T

107

Baumüller Nürnberg GmbH

5.94017.06

8.2.2 Warnings and messages

Parameter overview

ID no.

Name

Range

min. ... max.

Unit

Standard

value

Display

only

warnings and messages

Class 2 Diagnostics

181

Manufacturer Class 2 Diagnostics

32912

BUS warning

32913

supply warning

Class 3 Diagnostics

183

Manufacturer Class 3 Diagnostics

32914

BUS operating message

32915

BUS hardware message

32916

supply operating message

Parameter description

Class 2 Diagnostics

Shutdown advance warning - does not lead to controller inhibit or pulse inhibit.

Bit no.

Meaning

reserved

1: amplifier warning temperature exceeded

1: motor warning temperature exceeded

1: cooling error warning temperature exceeded

4 ... 14

reserved

bit set in Manufacturer Class 2 Diagnostics

Class 2 Diagnostics is read via the service channel.

Output X3:20 switches to high.

Manufacturer Class 2 Diagnostics

In Manufacturer Class 2 Diagnostics the manufacturer of the drive can define additional

shutdown advance warnings. If a warning is set or deleted in Manufacturer Class 2

Diagnostics, this leads to the setting of the manufacturer-specific warning in Class 2

Diagnostics.

Bit no.

Meaning

1: BUS warning

1 ... 5

reserved

1: BUG supply warning

7 ... 15

reserved

Summary of Contents for BUS 6-T Series
























































































































Search results

Summary of Contents for BUS 6-T Series

Reviews:

Related manuals for BUS 6-T Series

Brands by name

Popular brands

Baumuller BUS 6-T Series, Technical Description And Operations Manual

Search results

Summary of Contents for BUS 6-T Series

Reviews:

Related manuals for BUS 6-T Series

Brands by name

Popular brands