Baumuller BUS 6-T Series Technical Description And Operations Manual Download Page 17

Page: 17 / 119

Transport, removal of the packaging

Controller BUS 6 T

Baumüller Nürnberg GmbH

5.94017.06

3 T

RANSPORT

REMOVAL OF THE PACKAGING

The devices are packed in the manufacturer´s works in accordance with ordering instructions.

Severe vibrations during transport are to be avoided.

Onse packaging is removed and the devices are checked for their completeness, assembly can

follow.

Packaging material consists of cardboard, corrugated caroboard and/or wood. It can be disposed of in

accordance with local disposal regulations.

Any transport damage should be reported.

DANGER

In the event of damage being sustained in transit, the device should no be connected to a supply

without prior (high voltage) testing trained personnel.

Death, serious injury or considerable damage to equipment may result should this warning fail to be

heeded.

Summary of Contents for BUS 6-T Series
























































































































Search results

Summary of Contents for BUS 6-T Series

Reviews:

Related manuals for BUS 6-T Series

Brands by name

Popular brands

Baumuller BUS 6-T Series, Technical Description And Operations Manual

Search results

Summary of Contents for BUS 6-T Series

Reviews:

Related manuals for BUS 6-T Series

Brands by name

Popular brands