Baumuller BUS 6-T Series Technical Description And Operations Manual Download Page 2

Page: 2 / 119

BAUMÜLLER

CONTROLLER

BUS 6 T

Technical description and operation manual

Edition November 1995

5.94017.06

PLEASE READ AND PAY ATTENTION TO SAFETY INSTRUCTIONS

AND OPERATING GUIDE PRIOR TO COMMISSIONING

This manual contains the necessary information for normal opteration of the products described

therein. The drives may only be used, maintained and repaired by personnel familiar with the operation

manual and the applicable regulations on working safety and accident prevention. The devices are

manufactured to a high technical specification and are operationally safe. Provided that all safety

instructions habe been adhered to, there will be no personal danger during the installation and

commissioning stages.

The commisioning is prohibited until it has been positively determined that the machine, into which

these components are to be incorporated, complies with EC machine regulations.

This technical description replaces and nullifies all provious description. In order to provide the best

possible service, we reserve the right to alter information without notice.

Manufacturer and

Baumüller Nürnberg GmbH

Supplier's address:

Ostendstr. 80

90482 Nürnberg

Germany

Tel. (++49-911) 5432 - 0

Fax (++49-911) 5432 - 130

Copyright:

The technical description and the operation manual may not be copied or

duplicated without our permission.

Country of origin:

Made in Germany

Date of manufacture:

Determined from the serial number on the machine/motor.

Summary of Contents for BUS 6-T Series
























































































































Search results

Summary of Contents for BUS 6-T Series

Reviews:

Related manuals for BUS 6-T Series

Brands by name

Popular brands

Baumuller BUS 6-T Series, Technical Description And Operations Manual

Search results

Summary of Contents for BUS 6-T Series

Reviews:

Related manuals for BUS 6-T Series

Brands by name

Popular brands