manualshive.com logo in svg

Arris C4, User Manual

The DiGidot C4 product offers endless lighting control possibilities. With its advanced features and user-friendly interface, this versatile device allows you to create stunning light shows effortlessly. Download the user manual for free at manualshive.com and unlock the full potential of your DiGidot C4 device.

Share
Download
background image

Chapter 42: Fully-Qualified Domain Name (FQDN) 

 

STANDARD Revision 1.0 

C4® CMTS Release 8.3 User Guide 

© 2016 ARRIS Enterprises LLC. All Rights Reserved. 

1075 

 

Name     : dsg-srv2.lab.arrisi.com   
IP Addr  :  
State    : IP does not exist 
Last Poll: 2011 March 24 09:49:25 
Name     : dsg-srv3.lab.arrisi.com   
IP Addr  :  
State    : Invalid IP  
Last Poll: 2011 March 24 09:49:25 
Name     : dsg-srv4.lab.arrisi.com   
IP Addr  : 10.192.68.4 
State    : Timeout 
Last Poll: 2011 March 24 09:49:25 
 

 

 

FQDN Rejection Scenarios 

Under certain circumstances attempts to configure an FQDN will fail or generate a log message. The following are some 
typical examples: 

 

If a DSG tunnel classifier with explicit source and group addresses has been configured, it must be deprovisioned 
before the same classifier can be used for an FQDN. If you do not first deprovision the DSG tunnel classifier, the CLI 
command to assign an FQDN will fail. 

 

If on the contrary a DSG tunnel classifier has been configured with an FQDN, then this DSG tunnel classifier cannot be 
reconfigured with explicit source and group addresses. The DSG tunnel classifier must first be deprovisioned before it 
can be reconfigured with explicit source and group addresses. 

 

If the FQDN feature has configured an IGMP statically provisioned multicast group that has been resolved to an IP 
address, any attempt by the user to create an IGMP statically provisioned multicast group with the same source and 
group addresses will fail. 

 

If the FQDN feature has configured an IGMP statically provisioned multicast group that has not yet been resolved to an 
IP address, and the user creates an IGMP statically provisioned multicast group with explicit addresses, and after that 
the FQDN resolves to the same source address, then this FQDN will be saved. The C4/c CMTS will generate a log 
message to notify the user that this configuration may not be what he or she intended. The saved FQDN will take effect 
only if the IGMP statically provisioned multicast group with explicit IP addresses is deprovisioned. 

 

Summary of Contents for C4













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for C4

Calpeda IDROMAT 5 Quick Start Manual preview
IDROMAT 5
Brand: Calpeda Pages: 4
Ebyte E103-W03 Product Instruction Manual preview
E103-W03
Brand: Ebyte Pages: 38
EBS CPX200NB User Manual preview
CPX200NB
Brand: EBS Pages: 30
VAT 150 Series Installation, Operating, & Maintenance Instructions preview
150 Series
Brand: VAT Pages: 27
ICP DAS USA ET-7000 series User Manual preview
ET-7000 series
Brand: ICP DAS USA Pages: 148
ICMA S001 Technical Information Sheet preview
S001
Brand: ICMA Pages: 8
IDS X64 Manual preview
X64
Brand: IDS Pages: 2
MAKOT UMS-02 Manual preview
UMS-02
Brand: MAKOT Pages: 6
National Instruments IC-3173 Getting Started Manual preview
IC-3173
Brand: National Instruments Pages: 14
National Instruments SCXI-1104 Manual preview
SCXI-1104
Brand: National Instruments Pages: 11
Nauticam 25624 Instruction Manual preview
25624
Brand: Nauticam Pages: 2
National Instruments NI 9265 Getting Started Manual preview
NI 9265
Brand: National Instruments Pages: 18
National Instruments PXIe-4310 Calibration Procedure preview
PXIe-4310
Brand: National Instruments Pages: 10
National Instruments cRIO-9032 Getting Started Manual preview
cRIO-9032
Brand: National Instruments Pages: 20
NAPCO GEMINI C Series Installation Instructions Manual preview
GEMINI C Series
Brand: NAPCO Pages: 24
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Brand: RBI Pages: 128
S&C PMH Inspection Manual preview
PMH
Brand: S&C Pages: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Brand: S&C Pages: 24

Brands by name

Popular brands

Load more brands