ACS contsys RCE 300 Manual Download Page 45

Page: 45 / 152

ACS-CONTROL-SYSTEM GmbH

l Lauterbachstr. 57 l D-84307 Eggenfelden l www.acs-controlsystem.de l [email protected]

Universal Data Manager

Diagnostics and troubleshooting

Diagnost

ic code

Message text

Description

Remedy

M351

The device is

restarted.

The device is rebooting.
Causes include:

• Following a firmware update

• Change to device options

No action required. Message can be

acknowledged.

F431

Error:Calibration

Calibration data missing

Contact the Service Department

M502

Device is locked!

Device is locked! The message

appears when an attempt is made

to update the firmware, for

example.

Check lock per digital channel

F510

Setup was corrected. The device has discovered that the

configuration is no longer correct.

All the parameters affected have

been reset to the factory default

settings.
Possible causes:

• Input cards have been removed

or replaced by another type

• An input card is no longer

working correctly

A firmware update has caused

compatibility problems.
Note: This error message appears

each time the device is restarted

until at least one change has been

made to the configuration.

Please check the configuration of the

device. If hardware has been replaced,

no other action is needed

(recommendation: change the

operating language so that the error

message no longer appears after the

next restart).

M520

SMTP: Name could

not be resolved

(DNS)!
SNTP: Name could

not be resolved

(DNS)!

Problem with name resolution

(DNS).
SMTP: e-mail
SNTP: time synchronization

Check the corresponding settings

M528

Setup is not

compatible with this

firmware!

An attempt was made to load a

setup which is not compatible with

this firmware (e.g. another device

type)

Check whether the correct file has been

selected.

M530

Cannot copy setup.

An error occurred when a setup

was loaded from an SD card or USB

stick
An error occurred when a setup

was saved to an SD card or USB

stick

Replace the SD card or USB stick
Setup file defective?

S901

Input signal too

small

Input signal too small

Check the connections and parameters.

Check connected sensor/transmitter.

S902

Input signal too

high!

Input signal too high.

Check the connections and parameters.

Check connected sensor/transmitter.

M905

Set point x

Set point x has been violated

Note: Error number only occurs if e-

mails are sent

M906

End limit value x

Set point x no longer violated

Note: Error number only occurs if e-

mails are sent

F910

This software is not

enabled for this

device.

The current firmware is not

enabled for this hardware

Contact the Service Department

M920

Too many messages

that need to be

acknowledged!

There are too many messages that

need to be acknowledged. Another

message could not be added.

Acknowledge messages

M921

SD card x% full.

External memory is full

Replace SD card

Summary of Contents for RCE 300

























































































































































Search results

Summary of Contents for RCE 300

Reviews:

Related manuals for RCE 300

Brands by name

Popular brands

ACS contsys RCE 300, Manual

Search results

Summary of Contents for RCE 300

Reviews:

Related manuals for RCE 300

Brands by name

Popular brands