Zeiss humphrey HFA II-i series Скачать руководство пользователя страница 406

Страница: 406 / 521

ÚÚÚ

PROPRIETARY and CONFIDENTIAL

ÚÚÚ

SERVICE

BULLETIN

Instrument:

Humphrey Field Analyzer II-i

Subject:

740i to 745i Blue-Yellow Upgrade

No.:

FA2i-012

Date:

29 Jul 02

Status:

Informational

Pages:

General Information

The information and instructions provided in this service bulletin will enable a trained HFA II-i

technician to upgrade a model 740i to the Blue-Yellow option.

The upgrade from a model 740i to Blue-Yellow (becomes a model 745i) adds the capability to run

Blue-Yellow tests and enables Blue-Yellow Statpac.

Before You Start

Listed below are a number of questions and answers that you should review before beginning the

upgrade.

What is the minimum HFA II-i Model that can be upgraded to Blue-Yellow?

The following Marketing Department policy has been established: As a prerequisite to performing

the Blue-Yellow upgrade, ensure that the instrument is at minimum a model 740i.

What is the minimum skill level for a technician to perform the upgrade?

This upgrade should only be performed if the technician has complete parts removal and

replacement knowledge and complete instrument calibration knowledge. The procedures in this

service bulletin offer guidelines for performing the upgrade. It is assumed that the technician has

complete HFA II-i service knowledge.

How long will the upgrade take to complete?

The estimated time to complete the Blue-Yellow upgrade is 6.0 hours. This time takes into

account an instrument pre-checkout, hardware and software changes, an instrument post-

checkout, time to correct any unforeseen problems, and time to provide some limited customer

training.

Tools Required to Perform the Upgrade

Listed below are the tools required to perform the upgrade.

Description

Part No.

HFA II-i Service Manual and Service Bulletins . . . . . . . . .

52235

Soligor Light Meter Kit

. . . . . . . . . . . . . . . . . . .

14905

Soligor Mount Adaptor (HFA I/II) (set of 2) . . . . . . . . . . .

30248

Содержание humphrey HFA II-i series










































































































































































































































































































































































































































































































































Результаты поиска

Содержание humphrey HFA II-i series

Отзывы:

Похожие инструкции для humphrey HFA II-i series

Бренды по названию

Популярные бренды

Zeiss humphrey HFA II-i series, Руководство по обслуживанию на месте

Результаты поиска

Содержание humphrey HFA II-i series

Отзывы:

Похожие инструкции для humphrey HFA II-i series

Бренды по названию

Популярные бренды