Zeiss humphrey HFA II-i series Скачать руководство пользователя страница 275 | Manualshive

Страница: 275 / 521

background image

Humphrey Field Analyzer II - i

Appendix E

Confidential and Proprietary

52235C1105

E - 1

Field Service Guide

Appendix E. Instrument/BIOS Configuration

E.1 Instrument Configuration

This section provides a listing of configuration settings that are critical to the operation of
the

HFA II - i

unit.

Bootup Sequence

In the Advanced CMOS SETUP, the first boot device is IDE-0 (hard drive). The
instrument will not boot up a system disk from either the Magnetic Optical drive or the
floppy drive (if configured with the default settings). Special instructions have been
programmed in the instrument to recognize the installation disks and the Diagnostic
Support Tool disks. If an application diskette or the DST diskette are in the floppy drive
during instrument power up, the system will recognize them and allow the system to boot
from the floppy disk. If you attempt to load any other diagnostic software utilities that have
a system on the disk, you will need to first set the first boot device to floppy.

Note:

If you set the first boot device in the Advanced CMOS Setup to Floppy for

diagnostic purposes, it is necessary to reset the boot sequence to IDE-0 after using the
utility. Failure to do so will create a “Non-system disk or disk error Replace and strike any
key” any time a floppy disk is left in the floppy drive during the bootup sequence.

Changing the

BIOS Advanced CMOS Setup First Boot Device

1)

Set the

HFA II - i

system power switch to

ON

.

2)

Press and hold the

Delete

key.

3)

A

Enter current Password

dialogue will appear.

4)

Enter the password.

5)

The

AMIBIOS HIFLEX SETUP UTILITY

screen will appear.

6)

Use the down arrow key to select

Advanced CMOS Setup

.

7)

Press

Enter

.

8)

The

AMIOBIOS Setup - Advanced CMOS Setup

screen is displayed.

9)

Use the down arrow to select

1

st

Boot Device

.

10) Use the

PgUp

(page up) or

Pg Dn

(page down) keys to select the first boot device. Set the

first boot device to floppy if you plan on using the diagnostic utilities. Set the first boot
device to IDE-0 if you plan on resetting the instrument for normal operation.

«
...
273
274
275
276
277
...
»

Содержание humphrey HFA II-i series










































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для humphrey HFA II-i series

Бренд: Waltron Страницы: 11

Бренд: Labom Страницы: 6

Бренд: Labom Страницы: 5

Бренд: Magnum Energy Страницы: 3

Kotron 805 series

Бренд: Magnetrol Страницы: 36

Бренд: Magnescale Страницы: 104

Бренд: Magnescale Страницы: 44

Бренд: Valhalla Scientific Страницы: 43

Бренд: Vanguard Instruments Company Страницы: 62

Бренд: Vanguard Instruments Company Страницы: 58

Clavinova CLP-311

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 15

Бренд: Yamaha Страницы: 3

Alto Horn, Baritone, Euphonium

Бренд: Yamaha Страницы: 22

Clavinova CLP-320

Бренд: Yamaha Страницы: 2

Бренд: Yamaha Страницы: 20

Бренд: Mini Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды