manualshive.com logo in svg

Silicon Laboratories EFR32xG14 Wireless Gecko, Справочное руководство


Поделиться
Скачать
background image

When receiving a large frame, BYTESWAP in USARTn_CTRL determines the order the way the large frame is split into the two buffer
elements.  If  BYTESWAP  is  cleared,  the  least  significant  8  bits  of  the  received  frame  are  loaded  into  the  first  element  of  the  receive
buffer, and the remaining bits are loaded into the second element, as shown in 

Figure 18.13 USART Reception of Large Frames on

page 543

. The first byte read from the buffer thus contains the 8 least significant bits. Set BYTESWAP to reverse the order.

The status bits are loaded into both elements of the receive buffer. The frame is not moved from the receive shift register before there
are two free spaces in the receive buffer.

Status

RX buffer element 0

RX buffer element 1

Shift register

Peripheral Bus

Status

Status

0

1

2

3

4

5

6

7

0

1

2

0

1

2

0

1

2

3

4

5

6

7

Figure 18.13.  USART Reception of Large Frames

The two buffer elements can be read at the same time using the USARTn_RXDOUBLE or USARTn_RXDOUBLEX register. RXDATA0
then refers to buffer element 0 and RXDATA1 refers to buffer element 1.

Large frames can be used in both asynchronous and synchronous modes.

18.3.2.20  Multi-Processor Mode

To simplify communication between multiple processors, the USART supports a special multi-processor mode. In this mode the 9th da-
ta bit in each frame is used to indicate whether the content of the remaining 8 bits is data or an address.

When multi-processor mode is enabled, an incoming 9-bit frame with the 9th bit equal to the value of MPAB in USARTn_CTRL is identi-
fied as an address frame. When an address frame is detected, the MPAF interrupt flag in USARTn_IF is set, and the address frame is
loaded into the receive register. This happens regardless of the value of RXBLOCK in USARTn_STATUS.

Multi-processor mode is enabled by setting MPM in USARTn_CTRL, and the value of the 9th bit in address frames can be set in MPAB.
Note that the receiver must be enabled for address frames to be detected. The receiver can be blocked however, preventing data from
being loaded into the receive buffer while looking for address frames.

Figure 18.14 USART Multi-processor Mode Example on page 543

 explains basic usage of the multi-processor mode:

1. All slaves enable multi-processor mode and, enable and block the receiver. They will now not receive data unless it is an address

frame. MPAB in USARTn_CTRL is set to identify frames with the 9th bit high as address frames.

2.

The master sends a frame containing the address of a slave and with the 9th bit set

3. All slaves receive the address frame and get an interrupt. They can read the address from the receive buffer. The selected slave

unblocks the receiver to start receiving data from the master.

4.

The master sends data with the 9th bit cleared

5. Only the slave with RX enabled receives the data. When transmission is complete, the slave blocks the receiver and waits for a

new address frame.

Figure 18.14.  USART Multi-processor Mode Example

When  a  slave  has  received  an  address  frame  and  wants  to  receive  the  following  data,  it  must  make  sure  the  receiver  is  unblocked
before the next frame has been completely received in order to prevent data loss.

BIT8DV in USARTn_CTRL can be used to specify the value of the 9th bit without writing to the transmit buffer with USARTn_TXDATAX
or USARTn_TXDOUBLEX, giving higher efficiency in multi-processor mode, as the 9th bit is only set when writing address frames, and
8-bit writes to the USART can be used when writing the data frames.

Reference Manual

USART - Universal Synchronous Asynchronous Receiver/Transmitter

silabs.com

 | Building a more connected world.

Rev. 1.1  |  543

Содержание EFR32xG14 Wireless Gecko





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EFR32xG14 Wireless Gecko

IEI Technology WSB-H610 User Manual preview
WSB-H610
Бренд: IEI Technology Страницы: 187
IEI Technology TANK-XM811 User Manual preview
TANK-XM811
Бренд: IEI Technology Страницы: 71
National Instruments NI 9213 Getting Started preview
NI 9213
Бренд: National Instruments Страницы: 11
Zenith Data Systems Z-100 Series Installation Manual preview
Z-100 Series
Бренд: Zenith Data Systems Страницы: 64
NXP Semiconductors TWR-SB0410-36EVB User Manual preview
TWR-SB0410-36EVB
Бренд: NXP Semiconductors Страницы: 26
Amplifier Tech ATP6700 Owner'S Manual preview
ATP6700
Бренд: Amplifier Tech Страницы: 36
Genie WONVR216P5 Quick Start Manual preview
WONVR216P5
Бренд: Genie Страницы: 15
Altera Nios II Hardware Development Manual preview
Nios II
Бренд: Altera Страницы: 42
Cypress Semiconductor CY7C1381DV25 Specification Sheet preview
CY7C1381DV25
Бренд: Cypress Semiconductor Страницы: 28
H3C SecPath F50X0 Series Manual preview
SecPath F50X0 Series
Бренд: H3C Страницы: 41
Freescale Semiconductor KW2xD Series Reference Manual preview
KW2xD Series
Бренд: Freescale Semiconductor Страницы: 42
ST STM32L4P5AG User Manual preview
STM32L4P5AG
Бренд: ST Страницы: 37
Epson C32C824151 - UB E02 Print Server Technical Reference Manual preview
C32C824151 - UB E02 Print Server
Бренд: Epson Страницы: 84
Epson C11CA31101 User Manual preview
C11CA31101
Бренд: Epson Страницы: 168
Epson B80818 Series Quick Manual preview
B80818 Series
Бренд: Epson Страницы: 3
Velleman K8048 Manual preview
K8048
Бренд: Velleman Страницы: 14
Cambium Networks PMP/PTP 450 Series Quick Start Manual preview
PMP/PTP 450 Series
Бренд: Cambium Networks Страницы: 155
MikroTik CCR2004-16G-2S+PC Quick Manual preview
CCR2004-16G-2S+PC
Бренд: MikroTik Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды