manualshive.com logo in svg

Silicon Laboratories EFR32xG14 Wireless Gecko, Справочное руководство


Поделиться
Скачать
background image

5.1  Introduction

The Radio Transceiver of the EFR32 enables the user to control a wide range of settings and options for tailoring radio operation pre-
cisely  to  the  users  need.  It  provides  access  to  the  transmit  and  receive  data  buffers  and  supports  both  dynamic  and  static  frame
lengths, as well as automatic address filtering and CRC insertion/verification.

As seen in the Radio Overview illustration (

Figure 5.1 Radio Overview on page 115

), the radio consists of several modules all respon-

sible for specific tasks. Please refer to the abbreviations section (

Appendix 1. Abbreviations

) for a comprehensive description of acro-

nyms.

LNA

PA1

IFADC

IFADC

Demodulator

(DEMOD)

Fractional-N

Frequency

Synthesizer

Modulator

(MOD)

Frame Controller

(FRC)

Buf

fer Controller

 

(BUFC)

MA

T

C

H /

 FIL

TER

RFOUT1

Automatic 

Gain Control

(AGC)

Radio

 Controller

 

(RAC)

PA0

RFOUT0

RFIN

Radio Transceiver

CRC

Figure 5.1.  Radio Overview

During transmission (TX), the Radio Controller enables the SYNTH, Modulator and PA. The Modulator requests data from the Frame
Controller, which reads data from a buffer. Based upon modulation format and data to send, the Modulator manipulates the SYNTH to
output  the  correct  frequency  and  phase.  When  the  whole  frame  has  been  transmitted,  the  radio  can  automatically  switch  to  receive
mode.

In receive mode (RX), the radio controller enables the LNA, SYNTH, Mixer, ADC and Demodulator. The Demodulator searches for valid
frames according to modulation format and data rate. If a frame is detected, the demodulated data is handed to the Frame Controller,
which stores the data in the Buffer. When the complete frame has been received (determined by the Frame Controller), it is possible to
either go to TX or stay in RX to search for a new frame.

The Radio Transceiver interface is accessible through software drivers provided by Silicon Labs.

Reference Manual

Radio Transceiver

silabs.com

 | Building a more connected world.

Rev. 1.1  |  115

Содержание EFR32xG14 Wireless Gecko





















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EFR32xG14 Wireless Gecko

Mackie SP260 Installation Instructions preview
SP260
Бренд: Mackie Страницы: 2
Mackie SP260 Product Overview preview
SP260
Бренд: Mackie Страницы: 5
Patton electronics RocketLink-G 3088/I Getting Started Manual preview
RocketLink-G 3088/I
Бренд: Patton electronics Страницы: 61
Zenith Data Systems Z-100 Series Installation Manual preview
Z-100 Series
Бренд: Zenith Data Systems Страницы: 64
Dentsply Sirona inLab Speedcure 9494800 Instruction Manual preview
inLab Speedcure 9494800
Бренд: Dentsply Sirona Страницы: 91
Sennheiser Surround Dongle User Manual preview
Surround Dongle
Бренд: Sennheiser Страницы: 18
Lanner NCA-1525 User Manual preview
NCA-1525
Бренд: Lanner Страницы: 78
Z3 Technology SBE264-10-RPS User Instructions preview
SBE264-10-RPS
Бренд: Z3 Technology Страницы: 87
IDT Tsi310TM User Manual preview
Tsi310TM
Бренд: IDT Страницы: 207
Dahua D-NVR4108HS-4KS2/L Quick Start Manual preview
D-NVR4108HS-4KS2/L
Бренд: Dahua Страницы: 33
Lattice Semiconductor sysCLOCK ECP5 Usage Manual preview
sysCLOCK ECP5
Бренд: Lattice Semiconductor Страницы: 43
Paradyne ACCULINK 3161 CSU Quick Reference Manual preview
ACCULINK 3161 CSU
Бренд: Paradyne Страницы: 19
Gearlinx NR4400 Series User'S Quick Start Manual preview
NR4400 Series
Бренд: Gearlinx Страницы: 23
JETWAY I848ASR1A User Manual preview
I848ASR1A
Бренд: JETWAY Страницы: 47
Keysight Technologies U3024AH10 User'S And Service Manual preview
U3024AH10
Бренд: Keysight Technologies Страницы: 106
Kentrox RMM-1400 Configuration Manual preview
RMM-1400
Бренд: Kentrox Страницы: 246
Barracuda CloudGen Firewall Revision preview
CloudGen Firewall
Бренд: Barracuda Страницы: 8
Cypress Semiconductor CY7C027AV Specification Sheet preview
CY7C027AV
Бренд: Cypress Semiconductor Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды