manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 98

Type of connection

Connector

 

Encoder

X100

Siemens IX connector 

1)

Motor holding brake

X107

Included in the scope of sup‐

ply

1)

Part of the prefabricated MOTION-CONNECT OCC cable

The permissible cable lengths can be found in Chapter: "Cable lengths (Page 89)".

Note
Connection of motor holding brake, connector X107
Also connect the conductors for the motor holding brake to the connector at X107, even when 

you are using a motor without holding brake.

Shielded cables 

To ensure the proper functioning of the drive, use shielded cables for the connection of the 

motor (OCC cable with connection of encoder and holding brake), of the external braking 

resistor and of the fail-safe digital input.
Use the shield support that comes with the converter to connect the shield. Siemens 

recommends connecting the shield - as shown in the figure - with the shield clamp that comes 

with the prefabricated OCC cable for the motor connection.
● Connect the shield at both ends of the cable.
● Use cables with finely-stranded, braided shields.
● Do not interrupt the shield.

2&&FRQQHFWLRQFDEOHWRWKH

PRWRU

)HUULWHFRUHUHTXLUHGIRU)6%

IRU(0&&DWHJRU\&

&RQQHFWLRQFDEOHIRUH[WHUQDO

EUDNLQJUHVLVWRU

&RQQHFWLRQFDEOHIRUIDLOVDIHGLJLWDO

LQSXWDQGSUREH

Figure 5-11

Shield support with shield plate and shield clamps for prefabricated OCC cable

Installing
5.4 Connecting the converter and the motor

SINAMICS S210 servo drive system

96

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды