Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 308 | Manualshive

Страница: 308 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 308

Remedy:

- use the current version of the commissioning tool.
- modify the offline project and carry out a new download (e.g. compare the number of drive objects, motor, encoder, power

unit in the offline project and at the drive).
- change the drive state (is a drive rotating or is there a message/signal?).
- carefully note any other active messages/signals and remove their cause (e.g. correct any incorrectly set parameters).
- automatically calculate the control parameters (p0340). Then set p0010 = 0.
- boot from previously saved files (switch-off/switch-on or p0976).
- before a new download, restore the factory setting if the know-how protection was not activated on all drive objects.

F01044

CU: Descriptive data error

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

An error was detected when loading the descriptive data saved in the non-volatile memory.

Remedy:

Replace the memory card or Control Unit.

A01045

CU: Configuring data invalid

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

An error was detected when evaluating the parameter files PSxxxyyy.ACX, PTxxxyyy.ACX, CAxxxyyy.ACX, or

CCxxxyyy.ACX saved in the non-volatile memory. Because of this, under certain circumstances, several of the saved

parameter values were not able to be accepted. Also see r9406 up to r9408.
Alarm value (r2124, interpret hexadecimal):
Only for internal Siemens troubleshooting.

Remedy:

- check the parameters displayed in r9406 up to r9408, and correct these if required.
- Restore the factory setting using (p0976 = 1) and re-load the project into the drive unit.
Then save the parameterization in STARTER using the function "Copy RAM to ROM" or with p0977 = 1. This overwrites

the incorrect parameter files in the non-volatile memory – and the alarm is withdrawn.

A01049

CU: It is not possible to write to file

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

It is not possible to write into a write-protected file (PSxxxxxx.acx). The write request was interrupted.
Alarm value (r2124, interpret decimal):
Drive object number.

Remedy:

Check whether the "write protected" attribute has been set for the files in the non-volatile memory under .../USER/

SINAMICS/DATA/...
When required, remove write protection and save again (e.g. set p0977 to 1).

F01050

Memory card and device incompatible

Message value:

-

Drive object:

All objects

Reaction:

Servo: OFF2 (NONE, OFF1, OFF3)

Acknowledge:

IMMEDIATELY

Cause:

The memory card and the device type do not match (e.g. a memory card for SINAMICS S is inserted in SINAMICS G).

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

306

Operating Instructions, 12/2017, A5E41702836B AA

«
...
306
307
308
309
310
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды