Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 361 | Manualshive

Страница: 361 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 361

Remedy:

- re-commission the safety functions.
- upgrade the drive software.
- replace the memory card or drive.
For fault value = 129:
- activate the safety commissioning mode (p0010 = 95).
- adapt the PROFIsafe address (p9610).
- using the commissioning tool, copy the safety parameters and confirm the data change.
- exit the safety commissioning mode (p0010 = 0).
- save all parameters (copy RAM to ROM).
- carry out a POWER ON (switch-off/switch-on) for all components.
For fault value = 132:
- check the electrical cabinet design and cable routing for EMC compliance
Note:
CU: Control Unit
SI: Safety Integrated

F01657

SI P1 (CU): PROFIsafe telegram number invalid

Message value:

-

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

The PROFIsafe telegram number set in p9611 is not valid.
When PROFIsafe is enabled (p9601.3 = 1), then a telegram number greater than zero must be entered in p9611.
Note:
This fault does not result in a safety stop response.
See also: p9611, p60022, r60022

Remedy:

Check the telegram number setting (p9611).

F01658

SI P1 (CU): PROFIsafe telegram number differ

Message value:

-

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

The PROFIsafe telegram number is set differently in p9611 and r60022.
The telegram number must be identically set in both parameters.
Note:
This fault does not result in a safety stop response.
See also: p9611, p60022, r60022

Remedy:

Align the telegram number in both parameters so that they are the same (p9611, r60022).

F01659

SI P1 (CU): Write request for parameter rejected

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

359

«
...
359
360
361
362
363
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды