manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 313

132: Free BICO interconnection inhibited via p0922.
133: Access method not defined.
200: Below the valid values.
201: Above the valid values.
202: Cannot be accessed from the Basic Operator Panel (BOP).
203: Cannot be read from the Basic Operator Panel (BOP).
204: Write access not permitted.

Remedy:

- correct the parameterization in the commissioning tool and download the project again.
- enter the correct value in the specified parameter.
- identify the parameter that restricts the limits of the specified parameter.

A01097 (N)

NTP server cannot be accessed

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The selected NTP server (p3105[0...3]) cannot be accessed. Time synchronization cannot be performed.
Note:
NTP: Network Time Protocol

Remedy:

Correctly set the IP address of the NTP server, and check the connection to the NTP server.

Reaction upon N: NONE
Acknowl. upon N: NONE

A01099 (N)

UTC synchronization tolerance violated

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The tolerance (p3109) set for UTC synchronization was violated.
Note:
UTC: Universal Time Coordinates

Remedy:

Select the synchronization intervals shorter so that the deviation between the time of day master and drive system lies 

within the tolerance.
Note:
The deviation when synchronizing is shown in r3107.

Reaction upon N: NONE
Acknowl. upon N: NONE

F01105 (A)

CU: Insufficient memory

Message value:

%1

Drive object:

All objects

Reaction:

OFF1

Acknowledge:

POWER ON

Cause:

Too many functions have been configured on this Control Unit (e.g. too many drives, function modules, data sets, 

Technology Extensions, blocks, etc).
Fault value (r0949, interpret decimal):
Only for internal Siemens troubleshooting.

Remedy:

- change the configuration on this Control Unit (e.g. fewer drives, function modules, data sets, Technology Extensions, 

blocks, etc).
- use an additional Control Unit.

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

311

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды