Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 169

RDY

Explanation
Firmware update in progress for the connected DRIVE-CLiQ components.

DRIVE-CLiQ component firmware update has been completed.
Waiting for POWER ON of the corresponding components.
Remedy: Switch the component off and on again.

or

CU detection via DCP flashing.
Remark: Both options depend on the LED status when activating via DCP.

Table 7-3

Status explanation of the COM LED

COM

Explanation
No bus fault is present.
When the RDY LED lights up green and the COM LED is off, the converter is ready for

communication.
Temporary status after the supply voltage is switched on.

Bus ok. cyclic communication running perfectly

● Bus ok, however no setpoints (PLC in stop)
● In the isochronous mode: Bus ok, no synchronization

No bus connection
Remedy: Make sure that the bus cables are connected and are not damaged.

Bus error, possible causes:
● Incorrect configuration in the PLC (the same supplementary telegram has been set

twice?)

Table 7-4

Explanation of the RDY and COM LEDs - firmware update

RDY

COM

Explanation
Firmware update is active

LEDs are flashing synchronously:

Converter waits until the power supply is switched off and switched on again after

a firmware update

Diagnostics

7.1 Status displays and operating elements on the converter

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

167

«
...
167
168
169
170
171
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды