Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 527 | Manualshive

Страница: 527 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 527

Remedy:

- re-commission the safety functions.
- upgrade the drive software.
- replace the memory card or drive.
For fault value = 129:
- activate the Safety Integrated commissioning mode.
- adapt the PROFIsafe address.
- copy the safety parameters and confirm the data change.
- exit the Safety Integrated commissioning mode.
- save all parameters or "Copy RAM to ROM".
- carry out a POWER ON (switch-off/switch-on).
Note:
SI: Safety Integrated

F30657

SI P2: PROFIsafe telegram number invalid

Message value:

-

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

The PROFIsafe telegram number that has been set is not valid.
When PROFIsafe is enabled (p9601.3 = 1), then a telegram number greater than zero must be used.
The copy function was not used.
Note:
This fault does not result in a safety stop response.
See also: p9611, p60022, r60022

Remedy:

Enter a valid PROFIsafe telegram number (p9611), then using the commissioning tool, copy the safety parameters and

confirm the data change.

F30659

SI P2: Write request for parameter rejected

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

The write request for one or several Safety Integrated parameters in monitoring channel 2 was rejected.
Note:
See also fault F01659.

Remedy:

Upgrade the firmware to later version.

F30664

Error while booting

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

An error has occurred during booting.
Fault value (r0949, interpret hexadecimal):
Only for internal Siemens troubleshooting.

Remedy:

- carry out a POWER ON (switch-off/switch-on).
- upgrade firmware to later version.
- contact Technical Support.

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

525

«
...
525
526
527
528
529
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды