manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 406

A01980

PN: cyclic connection interrupted

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The cyclic connection to the PROFINET controller is interrupted.
See also: r8936 (PN cyclic connection state)

Remedy:

Establish the PROFINET connection and activate the PROFINET controller in the cyclic mode.

A01981

PN: Maximum number of controllers exceeded

Message value:

Info. 1: %1, info. 2: %2

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

A controller attempts to establish a connection to the drive, and as a consequence exceeds the permitted number of 

PROFINET connections.
The alarm disappears automatically after approx. 30 seconds.
Alarm value (r2124, interpret hexadecimal):
yyyyxxxx hex: yyyy = info. 1, xxxx = info. 2
Info 1 = 0: number of RT connections exceeded
Info 1 > 0: number of IRT connections exceeded
Info 2: permitted number of connections

Remedy:

Check the configuration of the PROFINET controllers.

A01982

PN: second controller missing

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

Connections to two PROFINET controllers are expected. However, only the connection to a PROFINET controller is 

present.
- there is only one connection to the F controller.
- system redundancy is activated.

Remedy:

Check the configuration of the PROFINET controllers.

A01983

PN: system redundancy switchover running

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The "PROFINET system redundancy" function is configured and the connection between the primary control and drive 

device is interrupted. The backup controller assumes control of the drive device.

Remedy:

Not necessary.
The alarm is automatically withdrawn after switchover has been successfully completed.

A01989

PN: internal cyclic data transfer error

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

404

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды