manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 727

Cause:

DRIVE-CLiQ communication error from the HF Damping Module to the Control Unit.
Fault cause:
11 (= 0B hex):
Synchronization error during alternating cyclic data transfer.
Note regarding the message value:
The individual information is coded as follows in the message value (r0949/r2124):
0000yyxx hex: yy = component number, xx = error cause

Remedy:

Carry out a POWER ON.
Note:
HF Damping Module

F37896

HF Damping Module (CU): Component properties inconsistent

Message value:

Component number: %1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

IMMEDIATELY

Cause:

The properties of the DRIVE-CLiQ component (HF Damping Module), specified by the fault value, have changed in an 

incompatible fashion with respect to the properties when booted. One cause can be, e.g. that a DRIVE-CLiQ cable or 

DRIVE-CLiQ component has been replaced.
Fault value (r0949, interpret decimal):
Component number.

Remedy:

- carry out a POWER ON.
- when a component is replaced, the same component type and if possible the same firmware version should be used.
- when a cable is replaced, only cables whose length is the same as or as close as possible to the length of the original 

cables should be used (ensure compliance with the maximum cable length).
Note:
HF Damping Module

F37899 (N, A) HF Damping Module: Unknown fault

Message value:

New message: %1

Drive object:

All objects

Reaction:

NONE (IASC/DCBRK, OFF1, OFF2, OFF3, STOP2)

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

A fault has occurred on the HF Damping Module that cannot be interpreted by the Control Unit firmware.
This can occur if the firmware on this component is more recent than the firmware on the Control Unit.
Fault value (r0949, interpret decimal):
Fault number.
Note:
If required, the significance of this new fault can be read about in a more recent description of the Control Unit.

Remedy:

- replace the firmware on the HF Damping Module by an older firmware version (r0168).
- upgrade the firmware on the Control Unit (r0018).
Note:
HF Damping Module

Reaction upon N: NONE
Acknowl. upon N: NONE
Reaction upon A: NONE
Acknowl. upon A: NONE

F37903

HF Damping Module: I2C bus error occurred

Message value:

%1

Drive object:

All objects

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

725

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды