Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 416 | Manualshive

Страница: 416 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 416

Remedy:

- insert or remove the memory card.
- use a larger memory card.
- configure a longer trace time or use an endless trace.
- avoid saving parameters while a multiple trace is running.
- check whether other functions are presently accessing measurement result files.

A02099

Trace: Insufficient Control Unit memory

Message value:

-

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The memory space still available on the Control Unit is no longer sufficient for the trace function.

Remedy:

Reduce the memory required, e.g. as follows:
- reduce the trace time.
- increase the trace clock cycle.
- reduce the number of signals to be traced.

A02100

Drive: Computing dead time current controller too short

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The value in p0118 produces a dead time of one clock cycle because it is prior to setpoint availability.
Possible causes:
- a parameter backup with a version higher than 4.3 was loaded to a version less than or equal to 4.3.
- the system properties after replacing a component no longer match the parameter assignment.
Alarm value (r2134, floating point):
Minimum value for p0118 where dead time no longer occurs.

Remedy:

- set p0118 to zero.
- set p0118 to a value greater than or equal to the alarm value (for p1810.11 = 1)
- set p0117 (from the device) to an automatic setting (p0117 = 1).
- check the firmware versions of the components involved.

A02150

TEC: Technology Extension cannot be loaded

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

The system was not able to load a Technology Extension.
Alarm value (r2124, interpret hexadecimal):
10 hex (16 dec):
The interface version in the DCB user library is not compatible to the DCC standard library that has been loaded.
12 hex (18 dec):
A technology package was not able to be downloaded to a Control Unit because the warm restart necessary was not able

to be performed.
Only for internal Siemens troubleshooting.

Faults and alarms
13.2 List of faults and alarms

SINAMICS S210 servo drive system

414

Operating Instructions, 12/2017, A5E41702836B AA

«
...
414
415
416
417
418
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды