manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 244

Note
Example:
r0975[0] = 42 --> SIEMENS
r0975[1] = 11 --> SERVO drive object type
r0975[2] = 102 --> first part, firmware version V01.02 (second part, refer to index 10)
r0975[3] = 2003 --> year 2003
r0975[4] = 1401 --> 14th of January
r0975[5] = 1 --> PROFIdrive drive object, type class
r0975[6] = 9 --> PROFIdrive drive object sub-type class 1
r0975[7] = 2 --> drive object number = 2
r0975[8] = 0 (reserved)
r0975[9] = 0 (reserved)
r0975[10] = 600 --> second part, firmware version (complete version: V01.02.06.00)

p0976

Reset all parameters

 

Changeable: C1(30)

Data type: Unsigned16

P group: Factory settings

Min: 0

Max: 1

Def: 0 

Description:

Resets all parameters of the drive system.

Value:

0:

Inactive

 

1:

Start reset of all parameters to factory setting

Dependency:

See also:  p0977

NOTICE
After changing the value, it is not possible to change parameters until the operation has been completed.

Note
After all of the parameters have been reset to their factory setting, the system must be commissioned for the first time 

again.
Reset is realized in the non-volatile memory.
Procedure:
1. Set p0009 = 30 (parameter reset).
2. Set p0976 = 1 The system is powered up again.
p0976 is automatically set to 0 and p0009 is automatically set to 1 after this has been carried out.

p0977

Save all parameters

 

Changeable: T, U

Data type: Unsigned16

P group: Factory settings

Min: 0

Max: 1

Def: 0 

Description:

Saves all parameters of the drive system to the non-volatile memory.
When saving, only the adjustable parameters intended to be saved are taken into account.

Value:

0:

Inactive

 

1:

Save in non-volatile memory - loaded at POWER ON

Dependency:

See also:  p0976

NOTICE
The drive power supply may only be switched off after data has been saved (i.e. after data save has been started, 

wait until the parameter again has the value 0).
Writing to parameters is inhibited while saving.

r0979[0...30]

PROFIdrive encoder format

 

Data type: Unsigned32

P group: Encoder

 

Description:

Displays the actual position encoder used according to PROFIdrive.

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

242

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды