manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 752

A.5

Certificates for the secure data transfer

A.5.1

Overview

The "Transport Layer Security" (TLS) protocol enables encrypted data transfer between a client 

and the SINAMICS drive. HTTPS access of the browser to the drive is based on the "Transport 

Layer Security" protocol. This section informs you which steps you need to follow to enable 

encrypted data transfer between a browser (client) and the SINAMICS (server).
You will find information on the configuration or your IP connection in Section: 

 "Configuring the IP connection (Page 158)" . 

Protecting the HTTPS access

The encrypted variant of the communication between the browser and the Web server using 

HTTPS requires the creation and installation of certificates.
Basically, there are three ways of creating a server certificate:
● Use the default configuration
● Use self-created certificates (by means of certificate software, such as OpenSSL)
● Use a server certificate from a certificate authority
You can only use the default configuration for SINAMICS S210, firmware version 5.1.

Delivery state
A private key is generated as a file on the device as default configuration when you first use 

HTTPS so that you can access the drive via HTTPS in the SINAMICS delivery state. During 

an HTTPS access using this key, a warning is issued in the browser that the certificate is 

unknown.

Duration of validity
The certificates are valid up to 2030.
After expiration of the validity period, install new valid certificates on all the relevant drives.

A.5.2

Using the certificate default configuration

Note
Security
The use of a default configuration described in the following is not the most secure way of 

transferring data using the HTTPS protocol to your drive with the Web server.
For this reason, it should only be used in secure networks (e.g. your PROFINET below a PLC) 

or for direct point-to-point connections on the Service interface X127.

Appendix
A.5 Certificates for the secure data transfer

SINAMICS S210 servo drive system

750

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды