manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 276

Description:

Sets the enable signals for the safety functions integrated in the drive and the type of selection.
Only a selection of the subsequently listed settings is permissible:
0000 hex:
Safety functions integrated in the drive inhibited (no safety function).
0001 hex:
Basis functions are enabled via the onboard terminals.
0008 hex:
Basis functions are enabled via PROFIsafe.
0009 hex:
Basis functions are enabled via PROFIsafe and onboard terminals.

Bit field:

Bit

Signal name

1 signal

0 signal

FP

 

00

STO enabled via terminals:

Enable

Inhibit

-

 

03

Enable PROFIsafe

Enable

Inhibit

-

Note
A change always becomes effective only after a POWER ON. Exception: change to p9601.0 becomes immediately 

effective.
STO: Safe Torque Off
SS1: Safe Stop 1 (corresponds to Stop Category 1 acc. to EN60204)
SI: Safety Integrated

p9602

SI enable safe brake control

 

Changeable: C2(95)

Data type: Integer16

P group: Safety Integrated

Min: 0

Max: 1

Def: 0 

Description:

Sets the enable for the "SBC" function.

Value:

0:

Inhibit SBC

 

1:

Enable SBC

Note
The "SBC" function is not activated until at least one safety monitoring function has been enabled (i.e. p9501 not equal 

to 0 and/or p9601 not equal to 0).
The parameterization "No motor holding brake available" and "Safe Brake Control" enabled (p1215 = 0, p9602 = 1) 

does not make sense if a motor holding brake is not being used.
SBC: Safe Brake Control
SI: Safety Integrated

p9610

SI PROFIsafe address

 

Changeable: C2(95)

Data type: Unsigned16

P group: Safety Integrated

Min: 0

Max: 65534

Def: 0 

Description:

Sets the PROFIsafe address.

Note
A change only becomes effective after a POWER ON.
The PROFIsafe address in the drive must be identical with the address in the control.

p9611

SI PROFIsafe telegram selection

 

Changeable: C2(95)

Data type: Unsigned16

P group: Safety Integrated

Min: 0

Max: 901

Def: 0 

Description:

Sets the PROFIsafe telegram number.

Value:

0:

No PROFIsafe telegram selected

 

30:

PROFIsafe standard telegram 30, PZD-1/1

 

901:

PROFIsafe SIEMENS telegram 901, PZD-3/5

Dependency:

See also:  p60022, r60022

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

274

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды