manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 351

Remedy:

- select STO and then de-select again.
- carry out a POWER ON (switch-off/switch-on) for all components.
- check whether there is a DRIVE-CLiQ communication error between the two monitoring channels and, if required, carry 

out a diagnostics routine for the faults identified.
- de-select all drive functions that are not absolutely necessary.
- check the electrical cabinet design and cable routing for EMC compliance
Note:
SI: Safety Integrated
STO: Safe Torque Off

F01630

SI P1 (CU): Brake control error

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

The drive-integrated "Safety Integrated" function in monitoring channel 1 has detected a brake control error and initiated 

a STOP A.
- OCC cable shield is not correctly connected.
- defect in the brake control circuit of the drive.
Fault value (r0949, decimal interpretation):
10, 11:
Fault in "open brake" operation.
- brake not closed or interrupted cable.
- ground fault in brake cable.
20:
Fault in "brake open" state.
- short-circuit in brake winding.
30, 31:
Fault in "close brake" operation.
- brake not closed or interrupted cable.
- short-circuit in brake winding.
40:
Fault in "brake closed" state.
50:
Fault in the brake control of the drive or a communication error (brake control diagnostics).

Remedy:

- select STO and then de-select again.
- check the motor holding brake connection.
- check the function of the motor holding brake.
- carry out a diagnostics routine for the faults involved.
- check for EMC-compliant control cabinet design and cable routing (e.g. shield OCC cable with shield terminal and shield 

plate, check the connection of the brake conductors).
- replace drive.
Note:
OCC: One Cable Connection (one cable system)
SBC: Safe Brake Control
SI: Safety Integrated
STO: Safe Torque Off
See also: p1215

A01631 (F, N) SI P1 (CU): motor holding brake/SBC configuration not practical

Message value:

-

Drive object:

All objects

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

349

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды