Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 553 | Manualshive

Страница: 553 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 553

Cause:

Trace data was saved in the component.

Remedy:

Not necessary.
Note:
For p7792= 1, the trace data of the component can be written to the memory card.

Reaction upon N: NONE
Acknowl. upon N: NONE

F30950

Power unit: Internal software error

Message value:

%1

Drive object:

All objects

Reaction:

OFF2

Acknowledge:

POWER ON

Cause:

An internal software error has occurred.
Fault value (r0949, interpret decimal):
Information about the fault source.
Only for internal Siemens troubleshooting.

Remedy:

- if necessary, upgrade the firmware in the power unit to a later version.
- contact Technical Support.

A30999 (F, N) Power unit: Unknown alarm

Message value:

New message: %1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Cause:

An alarm occurred on the power unit that cannot be interpreted by the Control Unit firmware.
This can occur if the firmware on this component is more recent than the firmware on the Control Unit.
Alarm value (r2124, interpret decimal):
Alarm number.
Note:
If required, the significance of this new alarm can be read about in a more recent description of the Control Unit.

Remedy:

- replace the firmware on the power unit by an older firmware version (r0128).
- upgrade the firmware on the Control Unit (r0018).

Reaction upon F: Servo: NONE (IASC/DCBRK, OFF1, OFF2, OFF3, STOP2)
Acknowl. upon F: IMMEDIATELY (POWER ON)
Reaction upon N: NONE
Acknowl. upon N: NONE

F31100 (N, A) Encoder 1: Zero mark distance error

Message value:

%1

Drive object:

All objects

Reaction:

Servo: ENCODER (IASC/DCBRK, NONE, OFF1, OFF2, OFF3, STOP2)

Acknowledge:

PULSE INHIBIT

Cause:

The measured zero mark distance does not correspond to the parameterized zero mark distance.
For distance-coded encoders, the zero mark distance is determined from zero marks detected pairs. This means that if a

zero mark is missing, depending on the pair generation, this cannot result in a fault and also has no effect in the system.
The zero mark distance for the zero mark monitoring is set in p0425 (rotary encoder) or p0424 (linear encoder).
Fault value (r0949, interpret decimal):
Last measured zero mark distance in increments (4 increments = 1 encoder pulse).
The sign designates the direction of motion when detecting the zero mark distance.

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

551

«
...
551
552
553
554
555
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды