manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 246

r1196

DSC position setpoint

 

Data type: Integer32

P group: Encoder

 

Description:

Displays the position setpoint of Dynamic Servo Control in fine pulses.

Note
DSC: Dynamic Servo Control

p1215

Motor holding brake configuration

 

Changeable: T

Data type: Integer16

P group: Functions

Min: 0

Max: 2

Def: 0 

Description:

Sets the configuration for the motor holding brake.
Re value 2:
This setting allows the motor shaft to be rotated for installation purposes.

Value:

0:

No motor holding brake available

 

1:

Motor holding brake acc. to sequence control

 

2:

Motor holding brake always open

Dependency:

See also:  p1216, r1216, p1217, r1217, p1226, p1227, p1228

CAUTION

For the setting p1215 = 0, if a brake is used, it remains closed. If the motor moves, this will destroy the brake.
Setting p1215 = 2 is not permissible if the brake is used to hold loads.

r1216

Motor holding brake opening time

 

Data type: FloatingPoint32

P group: Functions

 

Description:

Displays the opening time for the motor holding brake.
The speed setpoint is kept at 0 for this time. The speed setpoint is then enabled.

Recommendation:

This time should be set longer than the actual opening time of the brake. This ensures that the drive cannot accelerate 

when the brake is applied.

Dependency:

See also:  p1215, p1217, r1217

Note
For p1216 = 0 ms, the monitoring and the message A07931 "Brake does not open" are deactivated.

r1217

Motor holding brake closing time

 

Data type: FloatingPoint32

P group: Functions

 

Description:

Displays the time to close the motor holding brake.
If the drive signals that the motor is at a standstill, if the holding brake is activated, after the closing time has expired, 

the pulses are canceled. This prevents the load from sagging, for example.

Recommendation:

This time should be set longer than the actual closing time of the brake. This ensures that the pulses are only 

suppressed after the brake has closed.

Dependency:

See also:  p1215, p1216, r1216

NOTICE
If the selected closing time is too short with respect to the actual closing time of the brake, then the load can sag.
If the closing time is selected to be too long with respect to the actual closing time of the brake, the control works 

against the brake and therefore reduces its lifetime.

Note
For p1217 = 0 ms, the monitoring and the message A07932 "Brake does not close" are deactivated.

p1226[0]

Threshold for zero speed detection

 

Changeable: T, U

Data type: FloatingPoint32

P group: Functions

Min: 0.00 [rpm]

Max: 210000.00 [rpm]

Def: 20.00 [rpm] 

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

244

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды