Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 551 | Manualshive

Страница: 551 / 768

Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 551

F30896

Power unit DRIVE-CLiQ (CU): Inconsistent component properties

Message value:

Component number: %1

Drive object:

All objects

Reaction:

Servo: OFF2 (IASC/DCBRK, NONE, OFF1, OFF3, STOP2)

Acknowledge:

IMMEDIATELY

Cause:

The properties of the DRIVE-CLiQ component (power unit), specified by the fault value, have changed in an incompatible

fashion with respect to the properties when booted. One cause can be, e.g. that a DRIVE-CLiQ cable or DRIVE-CLiQ

component has been replaced.
Fault value (r0949, interpret decimal):
Component number.

Remedy:

- carry out a POWER ON.
- when a component is replaced, the same component type and if possible the same firmware version should be used.
- when a cable is replaced, only cables whose length is the same as or as close as possible to the length of the original

cables should be used (ensure compliance with the maximum cable length).

F30899 (N, A) Power unit: Unknown fault

Message value:

New message: %1

Drive object:

All objects

Reaction:

Servo: NONE (IASC/DCBRK, OFF1, OFF2, OFF3, STOP2)

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

A fault occurred on the power unit that cannot be interpreted by the Control Unit firmware.
This can occur if the firmware on this component is more recent than the firmware on the Control Unit.
Fault value (r0949, interpret decimal):
Fault number.
Note:
If required, the significance of this new fault can be read about in a more recent description of the Control Unit.

Remedy:

- replace the firmware on the power unit by an older firmware version (r0128).
- upgrade the firmware on the Control Unit (r0018).

Reaction upon N: NONE
Acknowl. upon N: NONE
Reaction upon A: NONE
Acknowl. upon A: NONE

F30903

Power unit: I2C bus error occurred

Message value:

%1

Drive object:

All objects

Reaction:

Servo: NONE (IASC/DCBRK, OFF1, OFF2, OFF3, STOP2)

Acknowledge:

IMMEDIATELY

Cause:

Communications error with an EEPROM or an analog/digital converter.
Fault value (r0949, interpret hexadecimal):
80000000 hex:
- internal software error.
00000001 hex ... 0000FFFF hex:
- module fault.

Remedy:

For fault value = 80000000 hex:
- upgrade firmware to later version.
For fault value = 00000001 hex ... 0000FFFF hex:
- replace the module.

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

549

«
...
549
550
551
552
553
...
»

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды