manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 278

Note
Pulse cancellation after failure of PROFIsafe communication is delayed by this time if "STOP B" is set (p9612 = 1).
SS1: Safe Stop 1 (corresponds to Stop Category 1 acc. to EN60204)

p9653

SI SS1 drive-based braking response

 

Changeable: C2(95)

Data type: Integer16

P group: Safety Integrated

Min: 0

Max: 1

Def: 0 

Description:

Sets the drive-based braking response for the "SS1" function.
In the factory setting, SS1 uses the OFF3 ramp.

Value:

0:

SS1 with OFF3

 

1:

SS1E external stop

Note
When p9653 is set = 1, the switchover is made from SS1 to SS1E - and the SS1 response is transferred to the control.
SS1E requires the externally initiated stop in order to be in conformance with stop Category 1 according to EN60204.
SS1: Safe Stop 1
SS1E: Safe Stop 1 external (Safe Stop 1 with external stop)

p9658

SI transition time STOP F to STOP A

 

Changeable: C2(95)

Data type: FloatingPoint32

P group: Safety Integrated

Min: 0.00 [ms]

Max: 30000.00 [ms]

Def: 0.00 [ms] 

Description:

Sets the transition period from STOP F to STOP A.

Dependency:

See also:  r9795
See also:  F01611

Note
The set time is rounded internally to an integer multiple of the monitoring clock cycle.
STOP F: Defect in a monitoring channel (error in the data cross-check)
STOP A: STO as a result of a fault detected by Safety Integrated

p9659

SI forced checking procedure timer

 

Changeable: C2(95)

Data type: FloatingPoint32

P group: Safety Integrated

Min: 0.00 [h]

Max: 9000.00 [h]

Def: 8760.00 [h] 

Description:

Setting the time interval in order to test safe torque off (STO).
During the test, within the parameterized time, an STO is selected and then again de-selected, e.g. by activating and 

deactivating Emergency Stop.
The monitoring time in r9660 is reset each time that STO is de-selected.

Dependency:

See also:  A01699

Note
STO: Safe Torque Off

r9660

SI forced checking procedure remaining time

 

Data type: FloatingPoint32

P group: Safety Integrated

 

Description:

Displays the remaining time until the next forced checking procedure of the safety functions.

Dependency:

See also:  A01699

p9670

SI module identification drive

 

Changeable: T

Data type: Unsigned32

P group: -

Min: 0

Max: 4294967295

Def: 0 

Description:

Safety Integrated module identifier for the drive.
Replacement of the drive is identified when the safety functions are activated.

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

276

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды