manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 184

8.1.7

Vibration response

Vibration severity grade
The vibration response of the system at the location of use is influenced by output elements, 

any built-on parts, the alignment, the installation, and external vibrations. This can change the 

vibration values of the motor.  
The motors conform to vibration severity grade A according to EN 60034-14 (IEC 60034-14).
The specified values refer only to the motor. The installation-dependent system vibration 

behavior can increase these values at the motor.
The vibration severity grade is maintained up to the rated speed (n

N

).

Q>USP@

*UDGH$

UPVSHUP

>PPV@

Y

      

Figure 8-1

Vibration severity levels

Permissible vibration in operation
In order to guarantee the proper function of the motor and not to impair the lifetime of the 

bearing, the following vibration values must be observed during operation.

● Vibration velocity 

1)

 V

rms

 according to ISO 10816 Max. 4.5 mm/s

● Vibration acceleration a

peak

 axial 

2)

50 m/s

2

● Vibration acceleration a

peak

 radial 

2)

50 m/s

2

1)

To measure the vibration velocity, the measuring equipment must fulfill the requirements of ISO 2954.

2)

The vibration acceleration is evaluated in the frequency range of 10 Hz to 2000 Hz.

The maximum peak in the time range is considered. 

Technical specifications
8.1 Technical data and properties of the motor

SINAMICS S210 servo drive system

182

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды