manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 258

Description:

Sets the configuration for One Button Tuning.

Bit field:

Bit

Signal name

1 signal

0 signal

FP

 

03

Speed precontrol

Yes

No

5045

 

04

Torque precontrol

Yes

No

5045

 

07

Voltage feedforward control

Yes

No

-

Dependency:

See also:  r5274

Note
For bit 03:
Activation of speed feedforward control.
For bit 04:
Activation of speed/torque feedforward control in the drive.
For bit 07:
Activation of the voltage precontrol.

r5274

One Button Tuning dynamic response estimated

 

Data type: FloatingPoint32

P group: -

 

Description:

Displays the estimated dynamic response of the speed control loop as PT1 time constant for One Button Tuning.
The lower the time constant, the higher the dynamic performance.

Dependency:

See also:  p5271

r5276[0]

One Button Tuning Kv factor estimated

 

Data type: FloatingPoint32

P group: -

 

Description:

Displays the estimated position controller gain (Kv factor) for One Button Tuning.

Dependency:

See also:  p5271

Note
The value for the closed-loop position control is required by a higher-level control system.

r5277[0]

One Button Tuning precontrol symmetrizing time estimated

 

Data type: FloatingPoint32

P group: -

 

Description:

Displays the estimated precontrol symmetrizing time for One Button Tuning.
This is required to symmetrize the position controller if the closed-loop position control is in an external control system.

Dependency:

See also:  p5271

p5291

FFT tuning configuration

 

Changeable: T, U

Data type: Unsigned16

P group: -

Min: -

Max: -

Def: 0000 0000 0011 1001 bin 

Description:

Sets the configuration for the "FFT tuning" function.
This function is used for One Button Tuning (p5300 = 1).

Bit field:

Bit

Signal name

1 signal

0 signal

FP

 

00

Noise excitation after pulse enable

Yes

No

-

 

01

Set current setpoint filter (HF)

Yes

No

-

 

02

Set speed controller gain (HF)

Yes

No

-

 

03

Length of FFT window bit 0 (LF, HF)

Yes

No

-

 

04

Length of FFT window bit 1 (LF, HF)

Yes

No

-

 

05

Windowing the time signals using a Hamming window (LF, 

HF)

Yes

No

-

 

06

Measure current controller

Yes

No

-

 

07

Bandwidth bit 0 (LF)

Yes

No

-

 

08

Bandwidth bit 1 (LF)

Yes

No

-

Parameters
12.2 List of parameters

SINAMICS S210 servo drive system

256

Operating Instructions, 12/2017, A5E41702836B AA

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды