manualshive.com logo in svg

Siemens SIMOTICS S-1FK2, Руководство по эксплуатации

Поделиться
Скачать
Siemens SIMOTICS S-1FK2 Скачать руководство пользователя страница 459

Drive object:

All objects

Reaction:

Servo: OFF2 (IASC/DCBRK, NONE, OFF1, OFF3, STOP2)

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

The requested position tracking for incremental encoders is not supported.
Fault value (r0949, interpret hexadecimal):
ccccbbaa hex
aa = encoder data set
bb = component number
cccc = fault cause
cccc = 00 hex = 0 dec
The encoder type does not support the "Position tracking incremental encoder" function.
cccc = 01 hex = 1 dec
Position tracking cannot be activated because the memory of the internal NVRAM is not sufficient or a Control Unit does 

not have an NVRAM.
cccc = 04 hex = 4 dec
A linear encoder is used that does not support the "position tracking" function.

Remedy:

- check the encoder parameterization (p0400, p0404).
- use a Control Unit with sufficient NVRAM.
- if required, de-select position tracking for the incremental encoder (p0411.3 = 0).

Reaction upon A: NONE
Acknowl. upon A: NONE

F07563 (A)

Drive encoder: XIST1_ERW configuration incorrect

Message value:

Fault cause: %1, encoder data set: %2

Drive object:

All objects

Reaction:

Servo: OFF2 (IASC/DCBRK, NONE, OFF1, OFF3, STOP2)

Acknowledge:

IMMEDIATELY (POWER ON)

Cause:

An incorrect configuration was identified for the "Absolute position for incremental encoder" function.
Fault value (r0949, interpret decimal):
Fault cause:
1 (= 01 hex):
The "Absolute value for incremental encoder" function is not supported (r0459.13 = 0).
Note regarding the message value:
The individual information is coded as follows in the message value (r0949/r2124):
yyxx dec: yy = fault cause, xx = encoder data set

Remedy:

For fault value = 1:
- upgrade the Sensor Module firmware version.
- check the mode (p4652 = 1, 3 requires the property r0459.13 = 1).

Reaction upon A: NONE
Acknowl. upon A: NONE

A07565 (F, N) Drive: Encoder error in PROFIdrive encoder interface 1

Message value:

%1

Drive object:

All objects

Reaction:

NONE

Acknowledge:

NONE

Faults and alarms

13.2 List of faults and alarms

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

457

Содержание SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды